- 您现在的位置：买卖IC网 > PDF目录10276 > AD7866ARUZ-REEL (Analog Devices Inc)IC ADC 12BIT 2CHAN DUAL 20TSSOP PDF资料下载
参数资料
| 型号： | AD7866ARUZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT 2CHAN DUAL 20TSSOP |
| 标准包装： | 2,500 |
| 位数： | 12 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 24mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 4 个单端，单极 |
| 配用： | EVAL-AD7866CBZ-ND - BOARD EVALUATION AD7866 |
REV. A
AD7866
–15–
100nF
2.5V
REF
ADC B
EXT REF
470nF
DCAPB
DCAPA
VREF
EXT REF
470nF
BUF B
ADC A
BUF A
Figure 15. Reference Circuit
If the on-chip 2.5 V reference is being used, and is to be applied
externally to the rest of the system, it may be taken from either
the VREF pin or one of the DCAPA or DCAPB pins. If it is taken
from the VREF pin, it must be buffered before being applied
elsewhere as it will not be capable of sourcing more than a few
microamps. If the reference voltage is taken from either the
DCAPA pin or DCAPB pin, a buffer is not strictly necessary. Either
pin is capable of sourcing current in the region of 100
A; how-
ever, the larger the source current requirement, the greater the
voltage drop seen at the pin. The output impedance of each of
these pins is typically 50
. In addition, this point represents
the actual voltage applied to the ADC internally so any voltage
drop due to the current load or disturbance due to a dynamic
load will directly affect the ADC conversion. For this reason, if a
large current source is necessary or a dynamic load is present, it
is recommended to use a buffer on the output to drive a device.
Examples of suitable external reference devices that may be ap-
plied at pins VREF, DCAPA, or DCAPB are the AD780, REF192,
REF43, and AD1582.
MODES OF OPERATION
The mode of operation of the AD7866 is selected by controlling
the (logic) state of the
CS signal during a conversion. There
are three possible modes of operation: normal mode, partial
power-down mode, and full power-down mode. The point at
which
CS is pulled high after the conversion has been initiated
will determine which power-down mode, if any, the device will
enter. Similarly, if already in a power-down mode,
CS can
control whether the device will return to normal operation or
remain in power-down. These modes of operation are designed
to provide flexible power management options. These options
can be chosen to optimize the power dissipation/throughput
rate ratio for differing application requirements.
Normal Mode
This mode is intended for fastest throughput rate performance
since the user does not have to worry about any power-up times
with the AD7866 remaining fully powered all the time. Figure 16
shows the general diagram of the operation of the AD7866 in
this mode.
The conversion is initiated on the falling edge of
CS, as described
in the Serial Interface section. To ensure that the part remains
fully powered up at all times,
CS must remain low until at least
10 SCLK falling edges have elapsed after the falling edge of
CS.
If
CS is brought high any time after the 10th SCLK falling edge,
but before the 16th SCLK falling edge, the part will remain
powered up but the conversion will be terminated and DOUTA
and DOUTB will go back into three-state. Sixteen serial clock
cycles are required to complete the conversion and access the
conversion result. The DOUT line will not return to three-state
after 16 SCLK cycles have elapsed, but instead when
CS is
brought high again. If
CS is left low for another 16 SCLK cycles,
the result from the other ADC on board will also be accessed on
the same DOUT line, as shown in Figure 22 (see also the Serial
Interface section). The STATUS bits provided prior to each
conversion result will identify which ADC the following result
will be from. Once 32 SCLK cycles have elapsed, the DOUT line
will return to three-state on the 32nd SCLK falling edge. If
CS is
brought high prior to this, the DOUT line will return to three-state
at that point. Thus,
CS may idle low after 32 SCLK cycles, until
it is brought high again sometime prior to the next conversion
(effectively idling
CS low), if so desired, since the bus will still
return to three-state upon completion of the dual result read.
Once a data transfer is complete and DOUTA and DOUTB have
returned to three-state, another conversion can be initiated after
the quiet time, tQUIET, has elapsed by bringing CS low again.
Partial Power-Down Mode
This mode is intended for use in applications where slower
throughput rates are required. Either the ADC is powered down
between each conversion, or a series of conversions may be
performed at a high throughput rate and the ADC is then powered
down for a relatively long duration between these bursts of several
conversions. When the AD7866 is in partial power-down, all
analog circuitry is powered down except for the on-chip reference
and reference buffer.
To enter partial power-down, the conversion process must be
interrupted by bringing
CS high anywhere after the second
falling edge of SCLK and before the tenth falling edge of SCLK
as shown in Figure 17. Once
CS has been brought high in this
window of SCLKs, the part will enter partial power-down, the
conversion that was initiated by the falling edge of
CS will be
SCLK
DOUTA
DOUTB
CS
STATUS BITS AND CONVERSION RESULT
1
16
10
Figure 16. Normal Mode Operation
相关PDF资料 |
PDF描述 |
|---|---|
| V24B3V3H150B2 | CONVERTER MOD DC/DC 3.3V 150W |
| D38999/26FJ19PALC | CONN HSG PLUG 19POS STRGHT PINS |
| MS27467T9F6S | CONN PLUG 6POS STRAIGHT W/SCKT |
| D38999/20KC98PNLC | CONN HSG RCPT 10POS WALL MT PINS |
| CS5532-ASZR | IC ADC 24BIT 2CH W/LNA 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7866ARUZ-REEL7 | 功能描述:IC ADC 12BIT 2CHAN DUAL 20TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7866BRU | 功能描述:IC ADC 12BIT 2CH DUAL 20-TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7866BRU-REEL | 制造商:Analog Devices 功能描述:ADC Dual SAR 1Msps 12-bit Serial 20-Pin TSSOP T/R |
| AD7866BRU-REEL7 | 功能描述:IC ADC 12BIT 2CH DUAL 20TSSOP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7866BRUZ | 功能描述:IC ADC 12BIT 2CH DUAL 20-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
发布紧急采购，3分钟左右您将得到回复。