- 您现在的位置：买卖IC网 > PDF目录294844 > AD7946 (Analog Devices, Inc.) 14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN PDF资料下载
参数资料
| 型号： | AD7946 |
| 厂商： | Analog Devices, Inc. |
| 英文描述： | 14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN |
| 中文描述： | 14位，500 kSPS的PulSAR系列⑩模数转换器，采用MSOP / QFN封装 |
| 文件页数： | 26/27页 |
| 文件大小： | 301K |
| 代理商： | AD7946 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页
AD7946
Preliminary Technical Data
Rev Pr D | Page 8 of 27
TERMINOLOGY
Integral Nonlinearity Error (INL)
Linearity error refers to the deviation of each individual code
from a line drawn from negative full scale through positive full
scale. The point used as negative full scale occurs 1/2 LSB
before the first code transition. Positive full scale is defined as a
level 1 1/2 LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line
(Figure 21).
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. DNL is the
maximum deviation from this ideal value. It is often specified in
terms of resolution for which no missing codes are guaranteed.
Offset Error
The first transition should occur at a level 1/2 LSB above analog
ground (152.6 V for the 0 V to 5 V range). The offset error is
the deviation of the actual transition from that point.
Gain Error
The last transition (from 111 . . . 10 to 111 . . . 11) should occur
for an analog voltage 1 1/2 LSB below the nominal full scale
(4.999542 V for the 0 V to 5 V range). The gain error is the
deviation of the actual level of the last transition from the ideal
level after the offset has been adjusted out.
Spurious-Free Dynamic Range (SFDR)
The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to S/(N+D) by the following formula
[
]
(
)
02
.
6
/
76
.
1
/
+
=
dB
D
N
S
ENOB
and is expressed in bits.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in dB.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in dB.
Signal-to-(Noise + Distortion) Ratio (S/[N+D])
S/(N+D) is the ratio of the rms value of the actual input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/(N+D) is expressed in dB.
Aperture Delay
Aperture delay is a measure of the acquisition performance and
is the time between the rising edge of the CNV input and when
the input signal is held for a conversion.
Transient Response
The time required for the ADC to accurately acquire its input
after a full-scale step function was applied.
相关PDF资料 |
PDF描述 |
|---|---|
| AD8138-EVAL | Low Distortion Differential ADC Driver |
| AD8138AR | Low Distortion Differential ADC Driver |
| AD8139ACP-REEL | Low Noise Rail-to-Rail Differential ADC Driver |
| AD8139ACP-REEL7 | Low Noise Rail-to-Rail Differential ADC Driver |
| AD8139ACPZ-REEL7 | Low Noise Rail-to-Rail Differential ADC Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD79461 | 制造商:AD 制造商全称:Analog Devices 功能描述:18-Bit, 2 MSPS PulSAR 15 mW ADC in LFCSP (QFN) |
| AD7946BCP | 制造商:Analog Devices 功能描述:ADC SGL SAR 500KSPS 14BIT SERL 10LFCSP EP - Bulk |
| AD7946BCPRL7 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN |
| AD7946BCPWP | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 500 kSPS PulSAR⑩ ADC in MSOP/QFN |
| AD7946BCPZRL | 功能描述:IC ADC 14BIT 500KSPS 10-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。