参数资料
| 型号： | AD8229HRZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC AMP INST LN 8SOIC |
| 标准包装： | 1 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 转换速率： | 22 V/µs |
| -3db带宽： | 15MHz |
| 电流 - 输入偏压： | 70nA |
| 电压 - 输入偏移： | 100µV |
| 电流 - 电源： | 6.7mA |
| 电流 - 输出 / 通道： | 35mA |
| 电压 - 电源，单路/双路(±)： | ±4 V ~ 17 V |
| 工作温度： | -40°C ~ 175°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SO |
| 包装： | 管件 |
AD8229
Data Sheet
Rev. B | Page 20 of 24
R
AD8229
+VS
+IN
–IN
0.1F
10F
0.1F
REF
VOUT
–VS
RG
CD
10nF
CC
1nF
CC
1nF
4.02k
0
94
12-
06
3
Figure 63. RFI Suppression
CD affects the difference signal, and CC affects the common-mode
signal. Values of R and CC should be chosen to minimize RFI. A
mismatch between R × CC at the positive input and R × CC at the
negative input degrades the CMRR of the AD8229. By using a
value of CD one magnitude larger than CC, the effect of the
mismatch is reduced, and performance is improved.
Resistors add noise; therefore, the resistor and capacitor values
chosen depend on the desired tradeoff between noise, input
impedance at high frequencies, and RFI immunity. The resistors
used for the RFI filter can be the same as those used for input
protection.
CALCULATING THE NOISE OF THE INPUT STAGE
The total noise of the amplifier front end depends on much
more than the 1 nV/√Hz headline specification of this data
sheet. There are three main contributors: the source resistance,
the voltage noise of the instrumentation amplifier, and the
current noise of the instrumentation amplifier.
In the following calculations, noise is referred to the input
(RTI). In other words, everything is calculated as if it appeared
at the amplifier input. To calculate the noise referred to the
amplifier output (RTO), simply multiple the RTI noise by the
gain of the instrumentation amplifier.
R2
RG
R1
SENSOR
AD8229
09
41
2-
06
4
Figure 64. AD8229 with Source Resistance from Sensor and
Protection Resistors
Source Resistance Noise
Any sensor connected to the AD8229 has some output resistance.
There may also be resistance placed in series with inputs for
protection from either overvoltage or radio frequency interference.
This combined resistance is labeled R1 and R2 in Figure 64. Any
resistor, no matter how well made, has a minimum level of noise.
This noise is proportional to the square root of the resistor
value. At room temperature, the value is approximately equal
to 4 nV/√Hz × √(resistor value in kΩ).
For example, assuming that the combined sensor and protection
resistance on the positive input is 4 kΩ, and on the negative
input is 1 kΩ, the total noise from the input resistance is
2
)
1
4
(
)
4
(
=
16
64
= 8.9 nV/ Hz
Voltage Noise of the Instrumentation Amplifier
The voltage noise of the instrumentation amplifier is calculated
using three parameters: the part input noise, output noise, and
the RG resistor noise. It is calculated as follows:
Total Voltage Noise =
2
)
(
)
(
)
/
(
Resistor
R
of
Noise
Input
G
Noise
Output
G
For example, for a gain of 100, the gain resistor is 60.4 Ω. Therefore,
the voltage noise of the in-amp is
2
)
0604
.
0
4
(
1
)
100
/
45
(
= 1.5 nV/√Hz
Current Noise of the Instrumentation Amplifier
Current noise is calculated by multiplying the source resistance
by the current noise.
For example, if the R1 source resistance in Figure 64 is 4 kΩ,
and the R2 source resistance is 1 k Ω, the total effect from the
current noise is calculated as follows:
)
5
.
1
(
)
5
.
1
4
((
2
= 6.2 nV/√Hz
Total Noise Density Calculation
To determine the total noise of the in-amp, referred to input,
combine the source resistance noise, voltage noise, and current
noise contribution by the sum of squares method.
For example, if the R1 source resistance in Figure 64 is 4 kΩ, the
R2 source resistance is 1 k Ω, and the gain of the in-amps is 100,
the total noise, referred to input, is
)
2
.
6
5
.
1
9
.
8
2
= 11.0 nV/√Hz
相关PDF资料 |
PDF描述 |
|---|---|
| AD822BR-REEL | IC OPAMP GP R-R 1.9MHZ LP 8SOIC |
| AD8230YRZ-REEL7 | IC AMP CHOPPER R-R PREC 8SOIC |
| AD8231TCPZ-EP-R7 | IC INSTR AMP PROGR ENH 16LFCSP |
| AD8231WACPZ-RL | IC AMP INST RRO 2.7MHZ 16LFCSP |
| AD8235ACBZ-P7 | IC AMP INSTR RRIO 23KHZ 11WLCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD8229HRZ-R7 | 功能描述:IC AMP INST LN 8SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:TS1854A View All Specifications 标准包装:50 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.25 V/µs 增益带宽积:630kHz -3db带宽:- 电流 - 输入偏压:16nA 电压 - 输入偏移:1000µV 电流 - 电源:162µA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 |
| AD8229XHDZ | 制造商:Analog Devices 功能描述:210 C CDIP IN AMP - Rail/Tube |
| AD822A/CHIPS | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Voltage-Feedback Operational Amplifier |
| AD822ACHIPS | 制造商:AD 制造商全称:Analog Devices 功能描述:Single Supply, Rail-to-Rail Low Power FET-Input Op Amp |
| AD822AN | 功能描述:IC OPAMP GP R-R 1.9MHZ DUAL 8DIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。