- 您现在的位置：买卖IC网 > PDF目录10531 > AD9219ABCPZ-40 (Analog Devices Inc)IC ADC 10BIT SRL 40MSPS 64LFCSP PDF资料下载
参数资料
| 型号： | AD9219ABCPZ-40 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/56页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT SRL 40MSPS 64LFCSP |
| 标准包装： | 1 |
| 位数： | 10 |
| 采样率（每秒）： | 40M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 4 |
| 功率耗散（最大）： | 313mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-VQ（7x7） |
| 包装： | 托盘 |
| 输入数目和类型： | 8 个单端，单极；4 个差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
Data Sheet
AD9219
Rev. E | Page 23 of 56
CLOCK INPUT CONSIDERATIONS
For optimum performance, the AD9219 sample clock inputs
(CLK+ and CLK) should be clocked with a differential signal.
This signal is typically ac-coupled to the CLK+ and CLK pins
via a transformer or capacitors. These pins are biased internally
and require no additional biasing.
Figure 52 shows a preferred method for clocking the AD9219. The
low jitter clock source is converted from a single-ended signal
to a differential signal using an RF transformer. The back-to-
back Schottky diodes across the secondary transformer limit
clock excursions into the AD9219 to approximately 0.8 V p-p
differential. This helps prevent the large voltage swings of the
clock from feeding through to other portions of the AD9219,
and it preserves the fast rise and fall times of the signal, which
are critical to low jitter performance.
0.1F
SCHOTTKY
DIODES:
HSM2812
CLK+
50
100
CLK–
CLK+
ADC
AD9219
Mini-Circuits
ADT1-1WT, 1:1Z
XFMR
05
72
6-
0
24
Figure 52. Transformer-Coupled Differential Clock
Another option is to ac-couple a differential PECL signal to the
sample clock input pins as shown in Figure 53. The AD9510/
drivers offers excellent jitter performance.
100
0.1F
240
50*
50*
CLK
*50 RESISTORS ARE OPTIONAL
CLK–
CLK+
ADC
AD9219
05
72
6
-02
5
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
PECL DRIVER
CLK+
CLK–
Figure 53. Differential PECL Sample Clock
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
100
0.1F
50*
CLK
*50 RESISTORS ARE OPTIONAL
CLK–
CLK+
ADC
AD9219
05
72
6-
0
26
LVDS DRIVER
CLK+
CLK–
Figure 54. Differential LVDS Sample Clock
In some applications, it is acceptable to drive the sample clock
inputs with a single-ended CMOS signal. In such applications,
CLK+ should be driven directly from a CMOS gate, and the
CLK pin should be bypassed to ground with a 0.1 μF capacitor
in parallel with a 39 kΩ resistor (see Figure 55). Although the
CLK+ input circuit supply is AVDD (1.8 V), this input is designed
to withstand input voltages of up to 3.3 V and therefore offers
several selections for the drive logic voltage.
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
0.1F
39k
50*
OPTIONAL
100
0.1F
CLK
*50 RESISTOR IS OPTIONAL
CLK–
CLK+
ADC
AD9219
05
72
6-
0
27
CLK
CMOS DRIVER
CLK+
Figure 55. Single-Ended 1.8 V CMOS Sample Clock
AD9510/AD9511/
AD9512/AD9513/
AD9514/AD9515
0.1F
50*
CLK
*50 RESISTOR IS OPTIONAL
0.1F
CLK–
CLK+
ADC
AD9219
05
72
6-
0
28
CLK
OPTIONAL
100
CMOS DRIVER
CLK+
Figure 56. Single-Ended 3.3 V CMOS Sample Clock
Clock Duty Cycle Considerations
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals. As a result, these ADCs may
be sensitive to the clock duty cycle. Commonly, a 5% tolerance is
required on the clock duty cycle to maintain dynamic performance
characteristics. The AD9219 contains a duty cycle stabilizer (DCS)
that retimes the nonsampling edge, providing an internal clock
signal with a nominal 50% duty cycle. This allows a wide range
of clock input duty cycles without affecting the performance of
the AD9219. When the DCS is on, noise and distortion perfor-
mance are nearly flat for a wide range of duty cycles. However,
some applications may require the DCS function to be off. If so,
keep in mind that the dynamic range performance can be affected
when operated in this mode. See the Memory Map section for
more details on using this feature.
Jitter in the rising edge of the input is an important concern, and it
is not reduced by the internal stabilization circuit. The duty
cycle control loop does not function for clock rates of less than
20 MHz nominal. The loop has a time constant associated with
it that must be considered in applications where the clock rate
can change dynamically. This requires a wait time of 1.5 μs to
5 μs after a dynamic clock frequency increase (or decrease)
before the DCS loop is relocked to the input signal. During the
period that the loop is not locked, the DCS loop is bypassed and
the internal device timing is dependent on the duty cycle of the
input clock signal. In such applications, it may be appropriate to
disable the duty cycle stabilizer. In all other applications, enabling
the DCS circuit is recommended to maximize ac performance.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3101A12S-3S | CONN RCPT 2POS FREE HNG W/SCKT |
| AD7686CRMZ | IC ADC 16BIT 500KSPS 10MSOP |
| VI-J41-MW-F2 | CONVERTER MOD DC/DC 12V 100W |
| AD7864ASZ-2 | IC ADC 12BIT PAR 520K 4CH 44MQFP |
| PT06A-14-15S | CONN PLUG 15POS W/SOCKETS SOLDER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9219ABCPZ-65 | 功能描述:IC ADC 10BIT SRL 65MSPS 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD9219ABCPZRL7-40 | 功能描述:IC ADC 10BIT SRL 40MSPS 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD9219ABCPZRL7-65 | 功能描述:IC ADC 10BIT SRL 65MSPS 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD9219BCPZ-40 | 制造商:Analog Devices 功能描述:ADC Quad Pipelined 40Msps 10-bit Serial 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:IC 10BIT ADC QUAD 40MSPS LFCSP48 |
| AD9219BCPZ-65 | 制造商:Analog Devices 功能描述:ADC Quad Pipelined 65Msps 10-bit Serial 48-Pin LFCSP EP 制造商:Analog Devices 功能描述:IC 10BIT ADC QUAD 65MSPS LFCSP48 |
发布紧急采购，3分钟左右您将得到回复。