- 您现在的位置：买卖IC网 > PDF目录165343 > AD9643BCPZ-250 (ANALOG DEVICES INC) 2-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, QCC64 PDF资料下载
参数资料
| 型号： | AD9643BCPZ-250 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | ADC |
| 英文描述： | 2-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, QCC64 |
| 封装： | 9 X 9 MM, ROHS COMPLIANT, MO-220VMMD-4, LFCSP-64 |
| 文件页数： | 25/36页 |
| 文件大小： | 1659K |
| 代理商： | AD9643BCPZ-250 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
AD9643
Rev. A | Page 31 of 36
MEMORY MAP
READING THE MEMORY MAP REGISTER TABLE
Each row in the memory map register table has eight bit locations.
The memory map is roughly divided into three sections: the chip
configuration registers (Address 0x00 to Address 0x02); the
channel index and transfer registers (Address 0x05 and
Address 0xFF); and the ADC functions registers, including setup,
control, and test (Address 0x08 to Address 0x59).
The memory map register table (see Table 14) documents the
default hexadecimal value for each hexadecimal address shown.
The column with the heading Bit 7 (MSB) is the start of the
default hexadecimal value given. For example, Address 0x14,
the output mode register, has a hexadecimal default value of
0x05. This means that Bit 0 = 1 and Bit 2 = 1, and the remaining
bits are 0s. This setting is the default output format value, which
is twos complement. For more information on this function and
others, see the AN-877 Application Note, Interfacing to High
Speed ADCs via SPI. This document details the functions
controlled by Register 0x00 to Register 0x25. The remaining
registers, Register 0x3A and Register 0x59, are documented in
the Memory Map Register Description section.
Open and Reserved Locations
All address and bit locations that are not included in Table 14
are not currently supported for this device. Unused bits of a
valid address location should be written with 0s. Writing to these
locations is required only when part of an address location is
open (for example, Address 0x18). If the entire address location
is open (for example, Address 0x13), this address location should
not be written.
Default Values
After the AD9643 is reset, critical registers are loaded with
default values. The default values for the registers are given in
the memory map register table, Table 14.
Logic Levels
An explanation of logic level terminology follows:
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
Transfer Register Map
Address 0x08 to Address 0x20, Address 0x3A, and
Address 0x59 are shadowed. Writes to these addresses do
not affect part operation until a transfer command is issued by
writing 0x01 to Address 0xFF, setting the transfer bit. This allows
these registers to be updated internally and simultaneously when
the transfer bit is set. The internal update takes place when the
transfer bit is set, and then the bit autoclears.
Channel-Specific Registers
Some channel setup functions, such as the signal monitor
thresholds, can be programmed to a different value for each
channel. In these cases, channel address locations are internally
duplicated for each channel. These registers and bits are designated
in Table 14 as local. These local registers and bits can be accessed
by setting the appropriate Channel A or Channel B bits in
Register 0x05. If both bits are set, the subsequent write affects
the registers of both channels. In a read cycle, only Channel A
or Channel B should be set to read one of the two registers. If
both bits are set during an SPI read cycle, the part returns the
value for Channel A. Registers and bits designated as global in
Table 14 affect the entire part and the channel features for which
independent settings are not allowed between channels. The
settings in Register 0x05 do not affect the global registers and bits.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9643BCPZRL7-210 | 2-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, QCC64 |
| AD9753ASTZRL | PARALLEL, WORD INPUT LOADING, 0.011 us SETTLING TIME, 12-BIT DAC, PQFP48 |
| ADA123AL7 | FIBER OPTIC ADD/DROP MUX/DEMUX, LC/UPC CONNECTOR |
| ADA123AB1 | FIBER OPTIC ADD/DROP MUX/DEMUX, FC/PC CONNECTOR |
| ADA123AB2 | FIBER OPTIC ADD/DROP MUX/DEMUX, FC/APC CONNECTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9643BCPZRL7-170 | 功能描述:模数转换器 - ADC 14 Bit 170Msps Dual ADC RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD9643BCPZRL7-210 | 功能描述:模数转换器 - ADC 14 Bit 210Msps Dual ADC RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD9643BCPZRL7-250 | 功能描述:模数转换器 - ADC 14 Bit 250Msps Dual ADC RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD9644-155KITZ | 功能描述:KIT EVAL FOR AD9644 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| AD9644-80KITZ | 功能描述:BOARD EVALUATION FOR AD9644 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
发布紧急采购，3分钟左右您将得到回复。