参数资料
| 型号： | AD9788BSVZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/64页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT 800MSPS 100TQFP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 设计资源： | Powering the AD9788 Using ADP2105 for Increased Efficiency (CN0141) |
| 标准包装： | 1,000 |
| 系列： | TxDAC® |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 450mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-TQFP 裸露焊盘 |
| 供应商设备封装： | 100-TQFP-EP（14x14） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 4 电流，单极；4 电流，双极 |
| 采样率（每秒）： | 800M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
AD9785/AD9787/AD9788
Rev. A | Page 28 of 64
The multichip synchronization register (MSCR) comprises four bytes located at Address 0x03.
Table 13. Multichip Synchronization Register (MSCR)
Address
Bit
Name
Description
0x03
[31:27]
Correlate Threshold
[4:0]
Sets the threshold for determining if the received synchronization data can be demodulated
accurately. A smaller threshold value makes the demodulator more noise immune; however,
the system becomes more susceptible to false locks (or demodulation errors).
[26]
SYNC_I enable
0: Default. The synchronization receive logic is disabled.
1: The synchronization receive logic is enabled.
[25]
SYNC_O enable
0: Default. The output synchronization pulse generation logic is disabled.
1: The output synchronization pulse generation logic is enabled.
[24]
Set low
This bit should always be set low.
[23:19]
SYNC_I Delay [4:0]
This value programs the value of the delay line of the SYNC_I signal. The delay line resolution
is 80 ps per step.
00000: nominal delay
00001: adds 80 ps delay to SYNC_I
00010: adds 160 ps delay to SYNC_I
…
11111: adds 2480 ps delay to SYNC_I
[18]
Sync error check mode
Specifies the synchronization pulse error check mode.
0: Manual error check
1: Automatic continuous error check
[17]
Set low
This bit should always be set low.
[16]
DATACLK input
0: Default. Slave mode is disabled.
1: Slave mode is enabled. Pin 37 functions as an input for the DATACLK signal, called DCI
(DATACLK input) in this mode. Depending on the state of Bit 1 in the DSCR register (Address
0x02), the sampling edge (where the data is latched into the AD9785/AD9787/AD9788) can
be programmed to be aligned with either the rising or falling edge of DCI. This mode can
only be used with 4× or 8× interpolation.
[15:11]
SYNC_O Delay [4:0]
This value programs the value of the delay line of the SYNC_O signal. The delay of SYNC_O is
relative to REFCLK. The delay line resolution is 80 ps per step.
00000: nominal delay
00001: adds 80 ps delay to SYNC_O
00010: adds 160 ps delay to SYNC_O
…
11111: adds 2480 ps delay to SYNC_O
[10]
Set high
This bit should always be set high.
[9]
SYNC_O polarity
0: Default. SYNC_O changes state on the rising edge of DACCLK.
1: SYNC_O is generated on the falling edge of DACCLK.
[8]
Sync loopback enable
0: Default. The AD9785/AD9787/AD9788 are not operating in internal loopback mode.
1: If the SYNC_O enable and Sync loopback enable bits are set, the AD9785/AD9787/AD9788
are operating in a mode in which the internal synchronization pulse of the device is used at
the multichip receiver logic and the SYNC_I+ and SYNC_I input pins are ignored. For proper
operation of the loopback synchronization mode, the synchronization driver enable and
sync enable bits must be set.
[7:4]
Clock State [3:0]
This value determines the state of the internal clock generation state machine upon
synchronization.
[3:0]
Sync Timing Margin
[3:0]
These bits are the synchronization window delay word. These bits are don’t care if the
synchronization driver enable bit is cleared.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9806KSTZ | IC CCD SIGNAL PROC 10BIT 48LQFP |
| AD9814JR | IC CCD SIGNAL PROC 14BIT 28-SOIC |
| AD9823KRUZRL7 | IC CDS FOR DGTL CAMERA 14-TSSOP |
| AD9824KCPZRL | IC CCD SIGNAL PROC 14BIT 48LFCSP |
| AD9826KRSZRL | IC IMAGE SGNL PROC 16BIT 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9788-DPG2-EBZ | 功能描述:BOARD EVALUATION FOR AD9788 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9788-EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9788 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board |
| AD9788MOD-EBZ | 制造商:Analog Devices 功能描述:DUAL 12-/14-/16-BIT 800 MSPS DAC WITH LOW POWER 32-BIT COMPLEX NCO 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk |
| AD9789BBC | 功能描述:数模转换器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| AD9789BBCRL | 制造商:Analog Devices 功能描述:QAM Encoder/Interpolator/Upconverter 164-Pin CSP-BGA T/R 制造商:Analog Devices 功能描述:QAM ENCODER/INTERPOLATOR/UPCNVRTR 164CSPBGA - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC 14BIT 2.4GSPS 4CH 164BGA 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14 Bit 2.5 GSPS D-A Converter 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14B 2400MSPS RF w/ 4CH Signal Process 制造商:Analog Devices 功能描述:CONVERTER - DAC |
发布紧急采购，3分钟左右您将得到回复。