参数资料
| 型号： | AD9788BSVZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 25/64页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT 800MSPS 100TQFP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 设计资源： | Powering the AD9788 Using ADP2105 for Increased Efficiency (CN0141) |
| 标准包装： | 1,000 |
| 系列： | TxDAC® |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 450mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-TQFP 裸露焊盘 |
| 供应商设备封装： | 100-TQFP-EP（14x14） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 4 电流，单极；4 电流，双极 |
| 采样率（每秒）： | 800M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
AD9785/AD9787/AD9788
Rev. A | Page 31 of 64
The interrupt control register comprises two bytes located at Address 0x09. Bits [11:10] and Bits [7:3] are read-only bits that indicate the
current status of a specific event that may cause an interrupt request (IRQ pin active low). These bits are controlled via the digital logic
and are read only via the serial port. Bits [1:0] are the IRQ mask (or enable) bits, which are writable by the user and can also be read back.
Table 19. Interrupt Control Register
Address
Bit
Name
Description
0x09
[15:13]
Reserved
Reserved for future use.
[12]
Clear lock indicator
Writing a 1 to this bit clears the sync lock lost status bit. This bit does not automatically
reset itself to 0 when the reset is complete.
[11]
Sync lock lost status
When high, this bit indicates that the device has lost synchronization. This bit is latched
and does not reset automatically after the device regains synchronization. To reset this
bit to 0, a 1 must be written to the clear lock indicator bit.
[10]
Sync lock status
When this bit is low, the device is not synchronized. When this bit is high, the device is
synchronized.
[9:8]
Reserved
Reserved for future use.
[7]
Data timing error IRQ
0: Default. No setup or hold time error has been detected via the input data port
setup/hold error checking logic.
1: A setup or hold time error has been detected via the input data port setup/hold error
checking logic.
[6]
Sync timing error IRQ
0: Default. No setup or hold time error has been detected via the multichip
synchronization receive pulse setup/hold error checking logic.
1: A setup or hold time error has been detected via the multichip synchronization
receive pulse setup/hold error checking logic.
[5]
Data timing error type
0: Default. A hold error has been detected via the input data port setup/hold error
checking logic. This bit is valid only if the data timing error IRQ bit (Bit 7) is set.
1: A setup error has been detected via the input data port setup/hold error checking
logic. This bit is valid only if the data timing error IRQ bit (Bit 7) bit is set.
[4]
Sync timing error type
0: Default. A hold error has been detected via the multichip synchronization receive
pulse setup/hold error checking logic. This bit is valid only if the sync timing error IRQ
bit (Bit 6) is set.
1: A setup error has been detected via the multichip synchronization receive pulse
setup/hold error checking logic. This bit is valid only if the sync timing error IRQ bit
(Bit 6) is set.
[3]
PLL lock indicator
0: Default. The PLL clock multiplier is not locked to the input reference clock.
1: The PLL clock multiplier is locked to the input reference clock.
[2]
Reserved
Reserved for future use.
[1]
Data port IRQ enable
0: Default. The data IRQ bit (and the IRQ pin) are not enabled (masked) for any errors
that may be detected via the input data port setup/hold error checking logic.
1: The data IRQ bit (and the IRQ pin) are enabled and go active if a setup or hold error is
detected via the input data port setup/hold error checking logic.
[0]
Sync port IRQ enable
0: Default. The sync IRQ bit (and the IRQ pin) are not enabled (masked) for any errors
that may be detected via the multichip synchronization receive pulse setup/hold error
checking logic.
1: The sync IRQ bit (and the IRQ pin) are enabled and go active if a setup or hold error
is detected via the multichip synchronization receive pulse setup/hold error checking
logic.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9806KSTZ | IC CCD SIGNAL PROC 10BIT 48LQFP |
| AD9814JR | IC CCD SIGNAL PROC 14BIT 28-SOIC |
| AD9823KRUZRL7 | IC CDS FOR DGTL CAMERA 14-TSSOP |
| AD9824KCPZRL | IC CCD SIGNAL PROC 14BIT 48LFCSP |
| AD9826KRSZRL | IC IMAGE SGNL PROC 16BIT 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9788-DPG2-EBZ | 功能描述:BOARD EVALUATION FOR AD9788 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9788-EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9788 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board |
| AD9788MOD-EBZ | 制造商:Analog Devices 功能描述:DUAL 12-/14-/16-BIT 800 MSPS DAC WITH LOW POWER 32-BIT COMPLEX NCO 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk |
| AD9789BBC | 功能描述:数模转换器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| AD9789BBCRL | 制造商:Analog Devices 功能描述:QAM Encoder/Interpolator/Upconverter 164-Pin CSP-BGA T/R 制造商:Analog Devices 功能描述:QAM ENCODER/INTERPOLATOR/UPCNVRTR 164CSPBGA - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC 14BIT 2.4GSPS 4CH 164BGA 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14 Bit 2.5 GSPS D-A Converter 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14B 2400MSPS RF w/ 4CH Signal Process 制造商:Analog Devices 功能描述:CONVERTER - DAC |
发布紧急采购，3分钟左右您将得到回复。