参数资料
| 型号： | AD9788BSVZRL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 44/64页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT 800MSPS 100TQFP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 设计资源： | Powering the AD9788 Using ADP2105 for Increased Efficiency (CN0141) |
| 标准包装： | 1,000 |
| 系列： | TxDAC® |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 450mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-TQFP 裸露焊盘 |
| 供应商设备封装： | 100-TQFP-EP（14x14） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 4 电流，单极；4 电流，双极 |
| 采样率（每秒）： | 800M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
AD9785/AD9787/AD9788
Rev. A | Page 49 of 64
Configuring the PLL Band Select Value
The PLL VCO has a valid operating range from approximately
1.0 GHz to 2.0 GHz covered in 63 overlapping frequency bands
as shown in Table 35. For any desired VCO output frequency,
there are multiple valid PLL band select values. Note that the
data shown in Table 35 is for a typical device. Device-to-device
variations can shift the actual VCO output frequency range by
30 MHz to 40 MHz. Also, the VCO output frequency varies as
a function of temperature. Therefore, it is required that the
optimal PLL band select value be determined for each
individual device at the particular operating temperature.
The device has an automatic PLL band select feature on chip.
When enabled, the device determines the optimal PLL band
setting for the device at the given temperature. This setting holds
for a ±60°C temperature swing in ambient temperature. If the
device operates in an environment that experiences a larger
temperature swing, an offset should be applied to the automat-
ically selected PLL band. The following procedure outlines a
method for setting the PLL band select value for a device
operating at a particular temperature that holds for a change in
ambient temperature over the total 40°C to +85°C operating
range of the device without further user intervention. (Note that
REFCLK must be applied to the device during this procedure.)
Configuring PLL Band Select with Temperature Sensing
The values of N1 (Register 0x04, Bits [14:13]) and N2
(Register 0x04, Bits [12:11]) should be programmed along
with the PLL settings shown in Table 34.
1.
Set the PLL Band Select [5:0] value (Register 0x04,
Bits [7:2]) to 63 to enable PLL auto mode.
2.
Wait for the PLL_LOCK pin or the PLL lock indicator
(Register 0x09, Bit 3) to go high. This should occur
within 5 ms.
3.
Read back the 6-bit PLL band select value (Register 0x04,
Bits [7:2]).
4.
Based on the temperature when the PLL auto mode is
enabled, set the PLL band indicated in Table 36 or Table 37
by rewriting the readback values into the PLL Band Select
[5:0] parameter (Register 0x04, Bits [7:2]).
Table 36. Setting Optimal PLL Band for Lower Range
(0 to 31) Bands
System Start-Up Temperature
Set PLL Band to
40°C to 10°C
Readback Band + 2
10°C to +15°C
Readback Band + 1
15°C to 55°C
Readback Band
55°C to 85°C
Readback Band 1
Table 37. Setting Optimal PLL Band for Higher Range
(32 to 62) Bands
System Start-Up Temperature
Set PLL Band to
40°C to 30°C
Readback Band + 3
30°C to 10°C
Readback Band + 2
10°C to +15°C
Readback Band + 1
15°C to 55°C
Readback Band
55°C to 85°C
Readback Band 1
Known Temperature Calibration with Memory
The procedure in the Configuring PLL Band Select with
Temperature Sensing section requires temperature sensing
upon start-up or reset of the device to choose the optimal PLL
band select value to hold over the entire operating temperature
range. If temperature sensing is not available in the system,
another option is to use the automatic PLL band select to
determine the optimal setting for the device when the device is
in a factory environment where the temperature is known. The
optimal band can then be stored in nonvolatile memory.
Whenever the system is powered up or restarted, the optimal
value can be loaded back into the device.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9806KSTZ | IC CCD SIGNAL PROC 10BIT 48LQFP |
| AD9814JR | IC CCD SIGNAL PROC 14BIT 28-SOIC |
| AD9823KRUZRL7 | IC CDS FOR DGTL CAMERA 14-TSSOP |
| AD9824KCPZRL | IC CCD SIGNAL PROC 14BIT 48LFCSP |
| AD9826KRSZRL | IC IMAGE SGNL PROC 16BIT 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9788-DPG2-EBZ | 功能描述:BOARD EVALUATION FOR AD9788 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9788-EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9788 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board |
| AD9788MOD-EBZ | 制造商:Analog Devices 功能描述:DUAL 12-/14-/16-BIT 800 MSPS DAC WITH LOW POWER 32-BIT COMPLEX NCO 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk |
| AD9789BBC | 功能描述:数模转换器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| AD9789BBCRL | 制造商:Analog Devices 功能描述:QAM Encoder/Interpolator/Upconverter 164-Pin CSP-BGA T/R 制造商:Analog Devices 功能描述:QAM ENCODER/INTERPOLATOR/UPCNVRTR 164CSPBGA - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC 14BIT 2.4GSPS 4CH 164BGA 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14 Bit 2.5 GSPS D-A Converter 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14B 2400MSPS RF w/ 4CH Signal Process 制造商:Analog Devices 功能描述:CONVERTER - DAC |
发布紧急采购，3分钟左右您将得到回复。