参数资料
| 型号： | AD9879BSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/32页 |
| 文件大小： | 0K |
| 描述： | IC PROCESSOR FRONT END 100MQFP |
| 标准包装： | 1 |
| 位数： | 12 |
| 通道数： | 5 |
| 功率（瓦特）： | 587mW |
| 电压 - 电源，模拟： | 3.3V |
| 电压 - 电源，数字： | 3.3V |
| 封装/外壳： | 100-BQFP |
| 供应商设备封装： | 100-MQFP（14x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD9879
Rev. A | Page 18 of 32
The default value for the clamp level control value is 0x20. This
results in an ADC output clamp level offset of 512 LSBs. The
valid programming range for the clamp level control value is
from 0x16 to 0x127.
REGISTER 0x08—ADC CLOCK CONFIGURATION
Bit 0: Send 10-Bit ADC Data Only
When this bit is set high, the device enters a nonmultiplexed
mode and only the data from the 10-bit ADC is sent to the IF
[11:0] digital output port.
Bit 1: Send 12-Bit ADC Data Only
When this bit is set high, the device enters a nonmultiplexed
mode and only data from the 12-bit ADC is sent to the IF [11:0]
digital output port.
Bit 3: Enable 7-Bits, IQ ADC
When this bit is active, the IQ ADC is put into 7-bit mode. In
this mode, the full-scale input range is 2 Vppd. When this bit is
set inactive, the IQ ADC is put into 6-bit mode and the full-
scale input voltage range is 1 Vppd.
Bit 4: Power-Down RXSYNC and IQ ADC Clocks
Setting this bit to 1 powers down the IQ ADC’s sampling clock
and stops the RXSYNC output pin. It can be used for additional
power saving on top of the power-down selections in Register 0x02.
Bit 5: Rx Port Fast Edge Rate
Setting this bit to 1 increases the output drive strength of all
digital output pins, except MCLK, REFCLK, Σ-Δ_OUT, and
FLAG1. These pins always have high output drive capability.
Bit 7: ADC Clocked Direct from OSCIN
When set high, the input clock at OSCIN is used directly as the
ADC sampling clock. When set low, the internally generated
master clock, MCLK, is divided by two and used as the ADC
sampling clock. Best ADC performance is achieved when the
ADCs are sampled directly from fOSCIN using an external crystal
or low jitter crystal oscillator.
REGISTER 0x0C—DIE REVISION
Bits 0–3: Version
The die version of the chip can be read from this register.
REGISTER 0x0D—Tx FREQUENCY TUNING WORDS
LSBs
This register accommodates two LSBs for both frequency
tuning words. For more information, see the description in the
REGISTER 0x0E—DAC GAIN CONTROL
Bits 0–3: DAC Fine Gain Control
This bit field sets the DAC gain if the Tx Path AD8321/AD8323
gain control select bit (Register F, Bit 3) is set to 0. The DAC
gain can be set from 0.0 dB to 7.5 dB in increments of 0.5 dB.
Table 6 details the programming.
Table 6. DAC Gain Control
Bits [3:0]
DAC Gain
0000
0.0 dB (default)
0001
0.5 dB
0010
1.0 dB
0011
1.5 dB
....
1110
7.0 dB
1111
7.5 dB
REGISTER 0x0F—Tx PATH CONFIGURATION
Bit 0: Single-Tone Tx Mode
Active high configures the AD9879 for single-tone applications
such as FSK. The AD9879 supplies a single frequency output as
determined by the frequency tuning word selected by the active
profile. In this mode, the TXIQ input data pins are ignored but
should be tied to a valid logic voltage level. The default value is
0 (inactive).
Bit 1: Spectral Inversion Tx
When set to 1, inverted modulation is performed.
MODULATOR_OUT = [I cos(ωt) + Q sin(ωt)]
(10)
The default is logic low, noninverted modulation.
MODULATOR_OUT = [I cos(ωt) + Q sin(ωt)]
(11)
Bit 2: Tx Path Bypass Sinc–1 Filter
Setting this bit high bypasses the digital inverse sinc filter of the
Tx path.
Bit 3: Tx Path AD8322/AD8327 Gain Control Mode
This bit changes the manner in which transmit gain control is
performed. Typically either AD8321/AD8323 (default 0) or
AD8222/AD8327 (default 1) variable gain cable drivers are
programmed over the chip’s 3-wire CA interface. The Tx gain
control select changes the interpretation of the bits in
Registers 0x13 and 0x17. See the Cable Driver Gain Control
section.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9901KQ | IC PHASE/FREQ DISCRIMR 14-CDIP |
| AD9920ABBCZRL | IC PROCESSOR CCD 12BIT 105CSPBGA |
| AD9978BCPZRL | IC PROCESSOR CCD 14BIT 40-LFCSP |
| ADADC71KD | IC ADC 16BIT HIGH RES 32-CDIP |
| ADADC80-Z-12 | IC ADC 12BIT INTEGRATED 32-CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9879BSZKL1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9879-EB | 制造商:Analog Devices 功能描述:Evaluation Board For Mixed Signal Front End Set Top Box, Cable Modem 制造商:Analog Devices 功能描述:DEV TOOLS, MIXED SGNL FRONT END SET TOP , CBL MODEM - Bulk |
| AD9880 | 制造商:Analog Devices 功能描述:AUDIO PROCESSOR - Bulk |
| AD9880/PCB | 制造商:AD 制造商全称:Analog Devices 功能描述:Analog/HDMI Dual Display Interface |
| AD9880/PCBZ | 功能描述:KIT EVALUATION AD9880 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:Advantiv® 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
发布紧急采购，3分钟左右您将得到回复。