收藏本站
参数资料
型号： ADE5569ASTZF62-RL
厂商： Analog Devices Inc
文件页数： 38/156页
文件大小： 0K
描述： IC METER/8052/RTC/LCD DRV 64LQFP
标准包装： 1,500
输入阻抗： *
测量误差： *
电压 - 高输入/输出： *
电压 - 低输入/输出： *
电流 - 电源： *
电源电压： *
测量仪表类型： *
工作温度： *
安装类型： 表面贴装
封装/外壳： 64-LQFP
供应商设备封装： 64-LQFP（10x10）
包装： 带卷 (TR)
ADE5166/ADE5169/ADE5566/ADE5569
TRANSITIONING BETWEEN OPERATING MODES
The operating mode of the ADE5166/ADE5169/ADE5566/
ADE5569 is determined by the power supply connected to
V SWOUT . Therefore, changes in the power supply, such as when
V SWOUT switches from V DD to V BAT or when V SWOUT switches to
V DD , alter the operating mode. This section describes events
that change the operating mode.
Automatic Battery Switchover (PSM0 to PSM1)
If any of the enabled battery switchover events occurs (see the
Battery Switchover section), V SWOUT switches to V BAT . This switch-
over results in a transition from PSM0 to PSM1 operating mode.
When battery switchover occurs, the analog circuitry used in
the ADE energy measurement DSP is disabled. To reduce power
consumption, user code can initiate a transition to PSM2 mode.
Entering Sleep Mode (PSM1 to PSM2)
To reduce power consumption when V SWOUT is connected to V BAT ,
user code can initiate sleep mode, PSM2, by setting Bit 4 in the
power control SFR (POWCON, Address 0xC5) to shut down the
MCU core. Events capable of waking the MCU can be enabled
(see the 3.3 V Peripherals and Wake-Up Events section).
Servicing Wake-Up Events (PSM2 to PSM1)
The ADE5166/ADE5169/ADE5566/ADE5569 may need to
wake up from PSM2 mode to service wake-up events (see the
3.3 V Peripherals and Wake-Up Events section). PSM1 code
execution begins at the power-on reset vector. After servicing
the wake-up event, the ADE5166/ADE5169/ADE5566/ADE5569
can return to PSM2 mode by setting Bit 4 in the power control SFR
(POWCON, Address 0xC5) to shut down the MCU core.
Automatic Switch to V DD (PSM2 to PSM0)
If the conditions to switch V SWOUT from V BAT to V DD occur (see the
Battery Switchover section), the operating mode switches to PSM0
mode. When this switch occurs, the MCU core and the analog
circuitry used in the ADE energy measurement DSP automatically
restart. PSM0 code execution begins at the power-on reset vector.
POWER SUPPLY
RESTORED
Data Sheet
Automatic Switch to V DD (PSM1 to PSM0)
If the conditions to switch V SWOUT from V BAT to V DD occur (see
the Battery Switchover section), the operating mode switches
to PSM0 mode. When this switch occurs, the analog circuitry
used in the ADE energy measurement DSP automatically restarts.
Note that code execution continues normally. A software reset
can be performed to start PSM0 code execution at the power-on
reset vector.
USING THE POWER MANAGEMENT FEATURES
Because program flow is different for each operating mode, the
status of V SWOUT must be known at all times. The VSWSOURCE bit
in the peripheral configuration SFR (PERIPH, Address 0xF4)
indicates the power supply to which V SWOUT is connected (see
Table 20). This bit can be used to control program flow on wake-
up. Because code execution always starts at the power-on reset
vector, Bit 6 of the PERIPH SRF can be tested to determine which
power supply is being used and to branch to normal code execution
or to wake up event code execution. Power supply events can
also occur when the MCU core is active. To be aware of the
events that change what V SWOUT is connected to, use the
following guidelines:
? Enable the battery switchover interrupt (EBSO)
if V SWOUT = V DD at power-up.
? Enable the power supply restored interrupt (EPSR)
if V SWOUT = V BAT at power-up.
An early warning that battery switchover is about to occur is
provided by SAG detection and, possibly, by low V DCIN
detection (see the Battery Switchover section).
For a user-controlled battery switchover, enable automatic battery
switchover on low V DD only. Next, enable the low V DCIN event to
generate the PSM interrupt. When a low V DCIN event occurs, start
data backup. Upon completion of the data backup, enable battery
switchover on low V DCIN . Battery switchover occurs 30 ms later.
PSM0
NORMAL MODE
AUTOMATIC BATTERY
SWITCHOVER
PSM1
BATTERY MODE
V SWOUT IS CONNECTED TO V DD
POWER SUPPLY
RESTORED
V SWOUT IS CONNECTED TO V BAT
WAKE-UP
EVENT
USER CODE DIRECTS MCU
TO SHUT DOWN CORE AFTER
SERVICING A WAKE-UP EVENT
PSM2
SLEEP MODE
V SWOUT IS CONNECTED TO V BAT
Figure 38. Transitioning Between Operating Modes
Rev. D | Page 38 of 156
相关PDF资料
PDF描述
HMC49DRTF-S13 CONN EDGECARD 98POS .100 EXTEND
VLF4014AT-100MR90 INDUCTOR POWER 10UH .9A SMD
CS5464-ISZ IC ENERGY METERING 1PHASE 28SSOP
ADE7752AARZ IC ENERGY METERING 3PHASE 24SOIC
ADE7816ACPZ-RL IC ENERGY METERING 40LFCSP
相关代理商/技术参数
参数描述
ADE-6 制造商:MINI 制造商全称:Mini-Circuits 功能描述:Surface Mount Frequency Mixer
ADE7116ASTZF16 功能描述:IC ENERGY METER 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7116ASTZF16-RL 功能描述:IC ENERGY METER 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7116ASTZF8 功能描述:IC ENERGY METER 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7116ASTZF8-RL 功能描述:IC ENERGY METER 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*