收藏本站
参数资料
型号： ADE5569ASTZF62-RL
厂商： Analog Devices Inc
文件页数： 57/156页
文件大小： 0K
描述： IC METER/8052/RTC/LCD DRV 64LQFP
标准包装： 1,500
输入阻抗： *
测量误差： *
电压 - 高输入/输出： *
电压 - 低输入/输出： *
电流 - 电源： *
电源电压： *
测量仪表类型： *
工作温度： *
安装类型： 表面贴装
封装/外壳： 64-LQFP
供应商设备封装： 64-LQFP（10x10）
包装： 带卷 (TR)
Data Sheet
Figure 59 illustrates how the phase compensation is used to
ADE5166/ADE5169/ADE5566/ADE5569
I 2 (t ) = I 2 – I 2 cos (2ω t )
remove a 0.1° phase lead in the current channel due to the
external transducer. To cancel the lead (0.1°) in the current
channel, a phase lead must also be introduced into the voltage
channel. The resolution of the phase adjustment allows the intro-
I(t ) = √2 × I sin(ω t )
INPUT
LPF3
IRMS
duction of a phase lead in increments of 0.026°. The phase lead is
I
achieved by introducing a time advance into the voltage channel.
A time advance of 4.88 μs is made by writing ?4 (0x3C) to the
time delay block, thus reducing the amount of time delay by
4.88 μs, or equivalently, a phase lead of approximately 0.1° at a
line frequency of 60 Hz (0x3C represents ?4 because the register
is centered with 0 at 0x40).
I P /I PA HPF
24
PGA1 ADC 1
I N LPF2
24
I 2 (t ) = I 2
Figure 60. IRMS Signal Processing
The I rms signal can be read from the waveform register by set-
ting the WAVMODE register (Address 0x0D) and setting the
WFSM bit (Bit 5) in the Interrupt Enable 3 SFR (MIRQENH,
Address 0xDB). Like the current and voltage channels waveform
sampling modes, the waveform data is available at sample rates of
25.6 kSPS, 12.8 kSPS, 6.4 kSPS, and 3.2 kSPS.
It is important to note that when the current input is larger than
V
V P
V N
PGA2
ADC 2
1
7
DELAY BLOCK
1.22μs/LSB
0
CHANNEL 2 DELAY
REDUCED BY 4.88μs
(0.1°LEAD AT 60Hz)
0x3C IN PHCAL[7:0]
V
40% of full scale, the I rms waveform sample register does not
represent the true processed rms value. The rms value processed
with this level of input is larger than the 24-bit read by the wave-
form register, making the value read truncated on the high end.
I
V
0.1°
1 0 0 1 0 1 1 1
PHCAL[7:0]
–231.93μs TO +48.83μs
I
Figure 61 and Figure 62 show the detail of the signal processsing
chain for the rms calculation on the current channel. The current
channel rms value is processed from the samples used in the
60Hz
Figure 59. Phase Calibration
RMS CALCULATION
60Hz
current channel waveform sampling mode and is stored in the
unsigned, 24-bit IRMS SFRs (IRMSL, Address 0xD4; IRMSM,
Address 0xD5; and IRMSH, Address 0xD6). One LSB of the
current channel rms register (IRMSL, IRMSM, and IRMSH) is
equivalent to 1 LSB of a current channel waveform sample.
× ∫ I 2 ( t ) dt
1
(1)
T
Current Channel RMS Calculation
The root mean square (rms) value of a continuous signal, I(t), is
defined as
T
I rms =
0
For time sampling signals, rms calculation involves squaring the
signal, taking the average, and obtaining the square root. The
ADE5166/ADE5169/ADE5566/ADE5569 implement this method
on the current channel by serially squaring the input, averaging
the results, and then taking the square root of the average. The
averaging part of this signal processing is done by
implementing a low-pass filter (LPF3 in Figure 60, Figure 61
and Figure 62).
The update rate of the current channel rms measurement is
4.096 MHz/5. To minimize noise in the reading of the register, the
I rms register can also be configured to update only with the zero
crossing of the voltage input. This configuration is done by setting
the ZXRMS bit (Bit 2) in the MODE2 register (Address 0x0C).
With the different specified full-scale analog input values, the ADC
produces an output code that is approximately ±0d2,684,354
(see the Current Channel ADC section). Similarly, the equiva-
lent rms value of a full-scale ac signal is 0d1,898,124 (0x1CF68C).
The current rms measurement provided in the ADE5166/
ADE5169/ADE5566/ADE5569 is accurate to within ±0.5%
for signal inputs between full scale and full scale/500. The
conversion from the register value to amps must be done
externally in the microprocessor using an amps/LSB constant.
This LPF has a ?3 dB cutoff frequency of 2 Hz when MCLK =
4.096 MHz.
I ( t ) = 2 × I sin( ω t )
where V is the rms voltage.
I 2 ( t ) = I 2 ? I 2 cos ( 2 ω t )
(2)
(3)
Current Channel RMS Offset Compensation
The ADE5166/ADE5169/ADE5566/ADE5569 incorporate a cur-
rent channel rms offset compensation register (IRMSOS). This is
a 12-bit, signed register that can be used to remove offset in the
current channel rms calculation. An offset can exist in the rms
calculation due to input noises that are integrated into the dc
When this signal goes through LPF3, the cos(2ωt) term is atte-
component of V 2 (t).
nuated and only the dc term, I rms2 (shown as I 2 in Figure 60),
goes through.
Rev. D | Page 57 of 156
相关PDF资料
PDF描述
HMC49DRTF-S13 CONN EDGECARD 98POS .100 EXTEND
VLF4014AT-100MR90 INDUCTOR POWER 10UH .9A SMD
CS5464-ISZ IC ENERGY METERING 1PHASE 28SSOP
ADE7752AARZ IC ENERGY METERING 3PHASE 24SOIC
ADE7816ACPZ-RL IC ENERGY METERING 40LFCSP
相关代理商/技术参数
参数描述
ADE-6 制造商:MINI 制造商全称:Mini-Circuits 功能描述:Surface Mount Frequency Mixer
ADE7116ASTZF16 功能描述:IC ENERGY METER 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7116ASTZF16-RL 功能描述:IC ENERGY METER 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7116ASTZF8 功能描述:IC ENERGY METER 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7116ASTZF8-RL 功能描述:IC ENERGY METER 64-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*