- 您现在的位置：买卖IC网 > PDF目录16316 > ADM1069ASTZ (Analog Devices Inc)IC SUPERVISOR/SEQUENCER 32-LQFP PDF资料下载
参数资料
| 型号： | ADM1069ASTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/32页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR/SEQUENCER 32-LQFP |
| 标准包装： | 1 |
| 系列： | Super Sequencer® |
| 类型： | 序列发生器 |
| 监视电压数目： | 8 |
| 输出： | 可编程 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-LQFP（7x7） |
| 包装： | 托盘 |
| 产品目录页面： | 788 (CN2011-ZH PDF) |
| 配用： | EVAL-ADM1069LQEBZ-ND - BOARD EVALUATION FOR ADM1069LQ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ADM1069
OUTPUTS
SUPPLY SEQUENCING THROUGH
CONFIGURABLE OUTPUT DRIVERS
Supply sequencing is achieved with the ADM1069 using the
programmable driver outputs (PDOs) on the device as control
signals for supplies. The output drivers can be used as logic
enables or as FET drivers.
The data driving each of the PDOs can come from one of three
sources. The source can be enabled in the PDOxCFG configuration
register (see the AN-721 Application Note for details).
The data sources are as follows:
? Output from the SE.
? Directly from the SMBus. A PDO can be configured so that
The sequence in which the PDOs are asserted (and, therefore, the
supplies are turned on) is controlled by the sequencing engine (SE).
The SE determines what action is taken with the PDOs based on
the condition of the ADM1069 inputs. Therefore, the PDOs can be
set up to assert when the SFDs are in tolerance, the correct input
signals are received on the VXx digital pins, no warnings are
received from any of the inputs of the device, and at other times.
?
the SMBus has direct control over it. This enables software
control of the PDOs. Therefore, a microcontroller can be
used to initiate a software power-up/power-down sequence.
On-chip clock. A 100 kHz clock is generated on the device.
This clock can be made available on any of the PDOs. It can
be used, for example, to clock an external device such as
an LED.
The PDOs can be used for a variety of functions. The primary
function is to provide enable signals for LDOs or dc-to-dc
converters that generate supplies locally on a board. The PDOs
can also be used to provide a PWRGD signal, when all the SFDs
are in tolerance, or a RESET output if one of the SFDs goes out
of specification (this can be used as a status signal for a DSP,
FPGA, or other microcontroller).
The PDOs can be programmed to pull up to a number of
different options. The outputs can be programmed as follows:
? Open-drain (allowing the user to connect an external pull-
up resistor).
? Open-drain with weak pull-up to V DD .
? Open-drain with strong pull-up to V DD .
? Open-drain with weak pull-up to VPx.
? Open-drain with strong pull-up to VPx.
DEFAULT OUTPUT CONFIGURATION
All of the internal registers in an unprogrammed ADM1069 device
from the factory are set to 0. Because of this, the PDOx pins are
pulled to GND by a weak (20 kΩ) on-chip pull-down resistor.
As the input supply to the ADM1069 ramps up on VPx or VH,
all PDOx pins behave as follows:
? Input supply = 0 V to 1.2 V. The PDOs are high impedance.
? Input supply = 1.2 V to 2.7 V. The PDOs are pulled to GND
by a weak (20 kΩ) on-chip pull-down resistor.
? Supply > 2.7 V. Factory programmed devices continue to
pull all PDOs to GND by a weak (20 kΩ) on-chip pull-down
resistor. Programmed devices download current EEPROM
configuration data, and the programmed setup is latched. The
PDO then goes to the state demanded by the configuration.
This provides a known condition for the PDOs during
?
?
Strong pull-down to GND.
Internally charge-pumped high drive
power-up.
The internal pull-down can be overdriven with an external pull-up
(12 V, PDO1 to PDO6 only) .
The last option (available only on PDO1 to PDO6) allows the
user to directly drive a voltage high enough to fully enhance an
external N-FET, which is used to isolate, for example, a card-
side voltage from a backplane supply (a PDO can sustain greater
than 10.5 V into a 1 μA load). The pull-down switches can also
be used to drive status LEDs directly.
of suitable value tied from the PDOx pin to the required pull-up
voltage. The 20 kΩ resistor must be accounted for in calculating
a suitable value. For example, if PDOx must be pulled up to 3.3 V,
and 5 V is available as an external supply, the pull-up resistor
value is given by
3.3 V = 5 V × 20 kΩ/( R UP + 20 kΩ)
Therefore,
R UP = (100 kΩ ? 66 kΩ)/3.3 V = 10 kΩ
VFET (PDO1 TO PDO6 ONLY)
VP4
V DD
SE DATA
SMBus DATA
CFG4 CFG5 CFG6
SEL
VP1
PDO
CLK DATA
Figure 25. Programmable Driver Output
Rev. C | Page 16 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| EET-UQ2C182CA | CAP ALUM 1800UF 160V 20% SNAP |
| 2-6278892-5 | CA,62.5,MTRJ-MTRJ |
| EET-ED2W121DA | CAP ALUM 120UF 450V 20% SNAP |
| LTC2928CUHF#PBF | IC PWR SUPPLY SEQUENCER 38-QFN |
| LTC691CSW#PBF | IC MPU SUPERVISRY CIRCUIT 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1069ASTZ-REEL | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| ADM1069ASTZ-REEL7 | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 其它有关文件:STM6905 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:5 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 140 ms 电压 - 阀值:2.188V，2.955V，可调，可调，可调 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-TSSOP 包装:Digi-Reel® 产品目录页面:1197 (CN2011-ZH PDF) 其它名称:497-8728-6 |
| ADM1070 | 制造商:AD 制造商全称:Analog Devices 功能描述:-48 V Hot Swap Controller |
| ADM1070ART | 制造商:AD 制造商全称:Analog Devices 功能描述:-48 V Hot Swap Controller |
| ADM1070ART-REEL | 制造商:Analog Devices 功能描述:Hot Swap Controller 1-CH -80V 6-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:6-PIN -48V HOT SWAP CONTROLLER I.C. - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:6-PIN -48V HOT SWAP CONTROLLER I.C. - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。