- 您现在的位置：买卖IC网 > PDF目录16316 > ADM1069ASTZ (Analog Devices Inc)IC SUPERVISOR/SEQUENCER 32-LQFP PDF资料下载
参数资料
| 型号： | ADM1069ASTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 22/32页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR/SEQUENCER 32-LQFP |
| 标准包装： | 1 |
| 系列： | Super Sequencer® |
| 类型： | 序列发生器 |
| 监视电压数目： | 8 |
| 输出： | 可编程 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-LQFP（7x7） |
| 包装： | 托盘 |
| 产品目录页面： | 788 (CN2011-ZH PDF) |
| 配用： | EVAL-ADM1069LQEBZ-ND - BOARD EVALUATION FOR ADM1069LQ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ADM1069
VIN
ADM1069
MICROCONTROLLER
DC-TO-DC
CONVERTER
OUTPUT
FEEDBACK
ATTENUATION
RESISTOR
VH/VPx/VXx
DACx
MUX
ADC
DAC
DEVICE
CONTROLLER
(SMBus)
GND
PCB
TRACE NOISE
DECOUPLING
CAPACITOR
Figure 33. Closed-Loop Margining System Using the ADM1069
WRITING TO THE DACS
Four DAC ranges are offered. They can be placed with midcode
(Code 0x7F) at 0.6 V, 0.8 V, 1.0 V, and 1.25 V. These voltages are
placed to correspond to the most common feedback voltages.
the current flowing through R3. Therefore, a direct relationship
exists between the extra voltage drop across R1 during margining
and the voltage drop across R3.
This relationship is given by the following equation:
Centering the DAC outputs in this way provides the best use of
the DAC resolution. For most supplies, it is possible to place the
Δ V OUT =
R1
R3
( V FB ? V DACOUT )
DAC midcode at the point where the dc-to-dc converter output
is not modified, thereby giving half of the DAC range to margin
up and the other half to margin down.
The DAC output voltage is set by the code written to the DACx
register. The voltage is linear with the unsigned binary number
in this register. Code 0x7F is placed at the midcode voltage, as
described previously. The output voltage is given by
DAC Output = ( DACx ? 0x7F)/255 × 0.6015 + V OFF
where V OFF is one of the four offset voltages.
There are 256 DAC settings available. The midcode value is
located at DAC Code 0x7F, as close as possible to the middle
of the 256 code range. The full output swing of the DACs is
+302 mV (+128 codes) and ?300 mV (?127 codes) around the
selected midcode voltage. The voltage range for each midcode
Table 10. Ranges for Midcode Voltages
where:
Δ V OUT is the change in V OUT .
V FB is the voltage at the feedback node of the dc-to-dc converter.
V DACOUT is the voltage output of the margining DAC.
This equation demonstrates that if the user wants the output
voltage to change by ±300 mV, then R1 = R3. If the user wants
the output voltage to change by ±600 mV, R1 = 2 × R3, and so on.
It is best to use the full DAC output range to margin a supply.
Choosing the attenuation resistor in this way provides the most
resolution from the DAC, meaning that with one DAC code
change, the smallest effect on the dc-to-dc converter output
voltage is induced. If the resistor is sized up to use a code such
as 27 decimal to 227 decimal to move the dc-to-dc converter
output by ±5%, it takes 100 codes to move 5% (each code moves
the output by 0.05%). This is beyond the readback accuracy of
the ADC, but it should not prevent the user from building a
circuit to use the most resolution.
Midcode
Voltage (V)
0.6
0.8
1.0
1.25
Minimum Voltage
Output (V)
0.300
0.500
0.700
0.950
Maximum Voltage
Output (V)
0.902
1.102
1.302
1.552
DAC LIMITING AND OTHER SAFETY FEATURES
Limit registers (called DPLIMx and DNLIMx) on the device
offer the user some protection from firmware bugs that can
cause catastrophic board problems by forcing supplies beyond
their allowable output ranges. Essentially, the DAC code written
into the DACx register is clipped such that the code used to set
CHOOSING THE SIZE OF THE ATTENUATION
RESISTOR
The size of the attenuation resistor, R3, determines how much
the DAC voltage swing affects the output voltage of the dc-to-dc
converter that is being margined (see Figure 33).
Because the voltage at the feedback pin remains constant, the
current flowing from the feedback node to GND through R2 is
a constant. In addition, the feedback node itself is high impedance.
This means that the current flowing through R1 is the same as
the DAC voltage is given by
DAC Code
= DACx, DACx ≥ DNLIMx and DACx ≤ DPLIMx
= DNLIMx, DACx < DNLIMx
= DPLIMx, DACx > DPLIMx
In addition, the DAC output buffer is three-stated if DNLIMx >
DPLIMx. By programming the limit registers this way, the user
can make it very difficult for the DAC output buffers to be turned
on during normal system operation. The limit registers are among
the registers downloaded from EEPROM at startup.
Rev. C | Page 22 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| EET-UQ2C182CA | CAP ALUM 1800UF 160V 20% SNAP |
| 2-6278892-5 | CA,62.5,MTRJ-MTRJ |
| EET-ED2W121DA | CAP ALUM 120UF 450V 20% SNAP |
| LTC2928CUHF#PBF | IC PWR SUPPLY SEQUENCER 38-QFN |
| LTC691CSW#PBF | IC MPU SUPERVISRY CIRCUIT 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1069ASTZ-REEL | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| ADM1069ASTZ-REEL7 | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 其它有关文件:STM6905 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:5 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 140 ms 电压 - 阀值:2.188V，2.955V，可调，可调，可调 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-TSSOP 包装:Digi-Reel® 产品目录页面:1197 (CN2011-ZH PDF) 其它名称:497-8728-6 |
| ADM1070 | 制造商:AD 制造商全称:Analog Devices 功能描述:-48 V Hot Swap Controller |
| ADM1070ART | 制造商:AD 制造商全称:Analog Devices 功能描述:-48 V Hot Swap Controller |
| ADM1070ART-REEL | 制造商:Analog Devices 功能描述:Hot Swap Controller 1-CH -80V 6-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:6-PIN -48V HOT SWAP CONTROLLER I.C. - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:6-PIN -48V HOT SWAP CONTROLLER I.C. - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。