- 您现在的位置：买卖IC网 > PDF目录9375 > ADN2850BCPZ25 (Analog Devices Inc)IC RHEO DGTL 10B DL 25K 16LFCSP PDF资料下载
参数资料
| 型号： | ADN2850BCPZ25 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/28页 |
| 文件大小： | 0K |
| 描述： | IC RHEO DGTL 10B DL 25K 16LFCSP |
| 产品变化通告： | Metal Edit Change 03/Feb/2012 |
| 标准包装： | 1 |
| 接片： | 1024 |
| 电阻（欧姆）： | 25k |
| 电路数： | 2 |
| 温度系数： | 标准值 35 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 3 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘，CSP |
| 供应商设备封装： | 16-LFCSP |
| 包装： | 托盘 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
ADN2850
Rev. E | Page 13 of 28
THEORY OF OPERATION
The ADN2850 digital programmable resistor is designed to
operate as a true variable resistor. The resistor wiper position is
determined by the RDAC register contents. The RDAC register
acts as a scratchpad register, allowing unlimited changes of
resistance settings. The scratchpad register can be programmed
with any position setting using the standard SPI serial interface by
loading the 24-bit data-word. In the format of the data-word, the
first four bits are commands, the following four bits are addresses,
and the last 16 bits are data. When a specified value is set, this
value can be stored in a corresponding EEMEM register. During
subsequent power-ups, the wiper setting is automatically loaded to
that value.
Storing data to the EEMEM register takes about 15ms and
consumes approximately 2 mA. During this time, the shift
register is locked, preventing any changes from taking place.
The RDY pin pulses low to indicate the completion of this
EEMEM storage. There are also 13 addresses with two bytes
each of user-defined data that can be stored in the EEMEM
register from Address 2 to Address 14.
The following instructions facilitate the programming needs of
the user (see Table 8 for details):
0. Do nothing.
1. Restore EEMEM content to RDAC.
2. Store RDAC setting to EEMEM.
3. Store RDAC setting or user data to EEMEM.
4. Decrement by 6 dB.
5. Decrement all by 6 dB.
6. Decrement by one step.
7. Decrement all by one step.
8. Reset EEMEM content to RDAC.
9. Read EEMEM content from SDO.
10. Read RDAC wiper setting from SDO.
11. Write data to RDAC.
12. Increment by 6 dB.
13. Increment all by 6 dB.
14. Increment by one step.
15. Increment all by one step.
Table 14 to Table 20 provide programming examples that use
some of these commands.
SCRATCHPAD AND EEMEM PROGRAMMING
The scratchpad RDAC register directly controls the position of
the digital resistor wiper. For example, when the scratchpad register
is loaded with all 0s, the wiper is connected to Terminal B of the
variable resistor. The scratchpad register is a standard logic
register with no restriction on the number of changes allowed,
but the EEMEM registers have a program erase/write cycle
limitation.
BASIC OPERATION
The basic mode of setting the variable resistor wiper position
(programming the scratchpad register) is accomplished by
loading the serial data input register with Instruction 11 (0xB),
Address 0, and the desired wiper position data. When the proper
wiper position is determined, the user can load the serial data
input register with Instruction 2 (0x2), which stores the wiper
position data in the EEMEM register. After 15 ms, the wiper
position is permanently stored in nonvolatile memory.
Table 6 provides a programming example listing the sequence of
the serial data input (SDI) words with the serial data output
appearing at the SDO pin in hexadecimal format.
Table 6. Write and Store RDAC Settings to EEMEM Registers
SDI
SDO
Action
0xB00100
0xXXXXXX
Writes data 0x100 to the RDAC1 register,
Wiper W1 moves to 1/4 full-scale position.
0x20XXXX
0xB00100
Stores RDAC1 register content into the
EEMEM1 register.
0xB10200
0x20XXXX
Writes Data 0x200 to the RDAC2 register,
Wiper W2 moves to 1/2 full-scale position.
0x21XXXX
0xB10200
Stores RDAC2 register contents into the
EEMEM2 register.
At system power-on, the scratchpad register is automatically
refreshed with the value previously stored in the corresponding
EEMEM register. The factory-preset EEMEM value is midscale.
The scratchpad register can also be refreshed with the contents
of the EEMEM register in three different ways. First, executing
Instruction 1 (0x1) restores the corresponding EEMEM value.
Second, executing Instruction 8 (0x8) resets the EEMEM values
of both channels. Finally, pulsing the
EE
AA
pin refreshes both
EEMEM settings. Operating the hardware control
AA
PREE
AA
function
requires a complete pulse signal. When
AA
PREE
AA
goes low, the internal
logic sets the wiper at midscale. The EEMEM value is not
loaded until
AA
PREE
AA
returns high.
PR
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B3K-MY-F1 | CONVERTER MOD DC/DC 40V 50W |
| ADN2850BCPZ250 | IC DGTL RHEO DL 1024POS 16LFCSP |
| VE-B3J-MY-F4 | CONVERTER MOD DC/DC 36V 50W |
| AD5232BRU10 | IC DGTL POT 256POS 10K 16TSSOP |
| VI-2NW-MX-B1 | CONVERTER MOD DC/DC 5.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADN2850BCPZ250 | 功能描述:IC DGTL RHEO DL 1024POS 16LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,300 系列:WiperLock™ 接片:257 电阻（欧姆）:100k 电路数:1 温度系数:标准值 150 ppm/°C 存储器类型:易失 接口:3 线 SPI（芯片选择） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VDFN 裸露焊盘 供应商设备封装:8-DFN-EP（3x3） 包装:带卷 (TR) |
| ADN2850BCPZ250-RL7 | 功能描述:IC DGTL RHEO DL 25K 9BIT16LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| ADN2850BCPZ25-RL7 | 功能描述:IC DGTL RHEO DL 25K 9BIT16LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| ADN2850BRU25 | 制造商:Analog Devices 功能描述: |
| adn2850bru25-rl7 | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。