- 您现在的位置：买卖IC网 > PDF目录16847 > ADN8830ACPZ (Analog Devices Inc)IC CTRLR THERMO COOLER 32-LFCSP PDF资料下载
参数资料
| 型号： | ADN8830ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/22页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR THERMO COOLER 32-LFCSP |
| 标准包装： | 1 |
| 应用： | 热电冷却器 |
| 电流 - 电源： | 8mA |
| 电源电压： | 3.3 V ~ 5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 托盘 |
| 产品目录页面： | 789 (CN2011-ZH PDF) |
| 其它名称： | 015-0070 Q2376189 |
ADN8830
To eliminate the resolution of the DAC as the principal source
Table I. Switching Frequencies vs. R FREQ
V STEP < 0 . 05 ° C × m
of system error, the step size of each bit, V STEP , should be lower
than the desired system resolution. A practical value for absolute
DAC resolution is the equivalent of 0.05 ° C. The value of V STEP
should be less than the value of m from Equation 8 multiplied
by the desired temperature resolution, or
(10)
where m is the slope of the voltage-to-temperature conversion
f SWITCH
100 kHz
250 kHz
500 kHz
750 kHz
1 MHz
R FREQ
1.5 M Ω
600 k Ω
300 k Ω
200 k Ω
150 k Ω
line, as found from Equation 8. From Design Example 2, where
m = 25 mV/ ° C, we see the DAC should have resolution better
For other frequencies, the value for this resistor, R FREQ , should
be set to
log ( V FS ) – log ( V STEP )
()
R FREQ =
than 1.25 mV per step.
The minimum number of bits required is then given as
Number of Bits =
log 2
(11)
150 × 10 9
(12)
f SWITCH
where f SWITCH is the switching frequency in Hz.
Higher switching frequencies reduce the voltage ripple across
where V FS is the full-scale output voltage from the DAC, which
should be equal to the reference voltage from the ADN8830,
VREF = 2.47 V as given in the Specifications table for the
Reference Voltage. In this example, the minimum resolution is
11 bits. A 12-bit DAC, such as the AD7390, can be readily
found.
It is important that the full-scale voltage input to the DAC is tied
to the ADN8830 reference voltage, as shown in Figure 4. This
eliminates errors from slight variances of VREF.
Thermistor Fault and Temperature Lock Indications
Both the THERMFAULT (Pin 1) and TEMPLOCK (Pin 5)
outputs are CMOS compatible outputs that are active high.
THERMFAULT will be a logic low while the thermistor is
operating normally and will go to a logic high if a short or
the TEC. However, high switch frequencies will create more
power dissipation in the external transistors. This is due to the
more frequent charging and discharging of the transistors’ gate
capacitances. If large transistors are needed for a high output
current application, faster switching frequencies could reduce
the overall power efficiency of the circuit. This is covered in
detail in the Calculating Power Dissipation and Efficiency section.
The switching frequency of the ADN8830 can be synchronized
with an external clock by connecting the clock signal to SYNCIN
(Pin 25). Pin 24 should also be connected to an R-C network, as
shown in Figure 6. This network is simply used to compensate a
PLL to lock on to the external clock. To ensure the quickest
synchronization lock-in time, R FREQ should be set to 1.5 M Ω .
open is detected at THERMIN (Pin 2). The trip voltage for
THERMFAULT is when THERMIN falls below 0.2 V or
ADN8830
COMPOSC
1nF
exceeds 2.0 V. THERMFAULT provides only an indication of
24
1k
0.1 F
a fault condition and does not activate any shutdown or protec-
tion circuitry on the ADN8830. To shut down the ADN8830, a
logic low voltage must be asserted on Pin 3, as described in the
Shutdown Mode section.
FREQ
26
1.5M
TEMPLOCK will output a logic high when the voltage at
Phase Shift ° = 360 ° ×
THERMIN is within 2.5 mV of TEMPSET. This voltage can
be related to temperature by solving for m from Equation 8. For
most laser diode applications, 2.5 mV is equivalent to ± 0.1 ° C.
If the voltage difference between THERMIN and TEMPSET is
greater than 2.5 mV, then TEMPLOCK will output a logic low.
The input offset voltage of the ADN8830 is guaranteed to within
250 μ V, which for most applications is within ± 0.01 ° C.
Setting the Switching Frequency
The ADN8830 has an internal oscillator to generate the switch-
ing frequency for the output stage. This oscillator can be either
set in free-run mode or synchronized to an external clock
signal. For free-run operation, SYNCIN (Pin 25) should be
connected to ground and COMPOSC (Pin 24) should be
connected to AVDD. The switching frequency is then set by a
single resistor connected from FREQ (Pin 26) to ground.
Table I shows R FREQ for some common switching frequencies.
Figure 6. Using an R-C Network on Pin 24 with
an External Clock
The relative phase of the ADN8830 internal oscillator compared
to the external clock signal can be adjusted. This is accomplished
by adjusting the voltage to PHASE (Pin 29) according to TPCs 3
and 4. The phase shift versus voltage can be approximated as
V PHASE
(13)
VREF
where V PHASE is the voltage at Pin 29, and VREF has a typical
value of 2.47 V.
To ensure the oscillator operates correctly, V PHASE should remain
higher than 100 mV and lower than 2.3 V. This is required for
either internal clock or external synchronization operation. A
resistor divider from VREF to ground can establish this voltage
easily, although any voltage source, such as a DAC, could be used
as well. If phase is not a consideration, for example with a single
ADN8830 being used, Pin 29 can be tied to Pin 6, which pro-
vides a 1.5 V reference voltage.
–10 –
REV. D
相关PDF资料 |
PDF描述 |
|---|---|
| MAX674CSA+T | IC VREF SERIES PREC 10V 8-SOIC |
| RSC06DRXN-S734 | CONN EDGECARD 12POS DIP .100 SLD |
| SDR1006-100ML | INDUCTOR POWER 10UH 2.6A SMD |
| AD9520-4/PCBZ | BOARD EVAL FOR AD9520-4 |
| AD9520-1/PCBZ | BOARD EVAL FOR AD9520-1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADN8830ACPZ-REEL | 功能描述:IC THERMO COOLER CNTRLR 32-LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ADN8830ACPZ-REEL7 | 功能描述:IC THERMO COOLER CTRLR 32-LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| ADN8830XCP-REEL | 制造商:Analog Devices 功能描述:- Tape and Reel |
| ADN8831 | 制造商:AD 制造商全称:Analog Devices 功能描述:Thermoelectric Cooler (TEC) Controller |
| ADN8831ACP | 制造商:Analog Devices 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。