- 您现在的位置：买卖IC网 > PDF目录1776 > ADP1111ANZ-12 (Analog Devices Inc)IC REG BUCK BST INV 12V .2A 8DIP PDF资料下载
参数资料
| 型号： | ADP1111ANZ-12 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/15页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BST INV 12V .2A 8DIP |
| 标准包装： | 50 |
| 类型： | 降压（降压），升压（升压），反相 |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 12V |
| 输入电压： | 2 V ~ 30 V |
| 频率 - 开关： | 72kHz |
| 电流 - 输出： | 200mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 供应商设备封装： | 8-PDIP |
ADP1111
Voltage-Controlled Positive-to-Negative Converter
By including an op amp in the feedback path, a simple positive-
to-negative converter can be made to give an output that is a
linear multiple of a controlling voltage, Vc. The op amp, an
OP196, rail-to-rail input and output amplifier, sums the
currents from the output and controlling voltage and drives the
FB pin either high or low, thereby controlling the on-board
oscillator. The 0.22 Ω resistor limits the short-circuit current to
about 3 A and, along with the BAT54 Schottky diode, helps
limit the peak switch current over varying input voltages. The
external power switch features an active pull-up to speed up the
turn-off time of the switch. Although an IRF9530 was used in
the evaluation, almost any device that can handle at least 3 A of
peak current at a VDS of at least 50 V is suitable for use in this
application, provided that adequate attention is paid to power
High Power, Low Quiescent Current Step-Down Converter
By making use of the fact that the feedback pin directly controls
the internal oscillator, this circuit achieves a shutdown-like state
by forcing the feedback pin above the 1.25 V comparator
threshold. The logic level at the 1N4148 diode anode needs to
be at least 2 V for reliable standby operation.
The external switch driver circuit features an active pull-up
device, a 2N3904 transistor, to ensure that the power MOSFET
turns off quickly. Almost any power MOSFET will do as the
switch as long as the device can withstand the 18 volt V GS and is
reasonably robust. The 0.22 Ω resistor limits the short-circuit
current to about 3 A and, along with the BAT54 Schottky
diode, helps to limit the peak switch current over varying input
voltages.
dissipation. The circuit can deliver 2 W of output power with a
+6-volt input from a control voltage range of 0 V to 5 V.
+8V TO +18V
INPUT R LIM
IRF9540
S D
LI
20 μ H
+5V
500mA
V IN
1k Ω
V IN I LIM
51 Ω
2N3904
121k Ω
+5V TO +12V
R LIM
INPUT
0.22 Ω
BAT54
2k Ω
2 1
V IN I LIM SW1 3
ADP1111
FB 8
AO SET GND SW2
6 7 5 4
NC NC
IRF9530
51 Ω
2N3904
1N4148 D1
IN5821
2 200k Ω
7
6
3
1N5231 4
L1 20 μ H
CTX20-4
C L +
47 μ F
35V
OUTPUT
–V OUT = –5.13 *V C
2W MAXIMUM OUTPUT
0.22
BAT54
2 1
SW1 3
ADP1111
FB 8
AO SET GND SW2
6 7 5 4
NC NC
OPERATE /STANDBY
2V ≤ V IN ≤ 5
1N4148
2k
+
G
D1
IN5821
1N4148
40.2k Ω
LI = COILTRONICS CTX20-4
C L
220 μ F
39k Ω
V C (0V TO +5V)
Figure 34. High Power, Low Quiescent Current Step-Down
Figure 32. Voltage Controlled Positive-to-Negative
Converter
+3 V to –22 V LCD Bias Generator
This circuit uses an adjustable-output version of the ADP1111
to generate a +22.5 V reference output that is level-shifted to
give an output of –22 V. If operation from a +5 volt supply is
desired, change R1 to 47 ohms. The circuit will deliver 7 mA
with a 3 volt supply and 40 mA with a 5 volt supply.
Converter
NOTES
1. All inductors referenced are Coiltronics CTX-series except
where noted.
2. If the source of power is more than an inch or so from the
converter, the input to the converter should be bypassed with
approximately 10 μ F of capacitance. This capacitor should
be a good quality tantalum or aluminum electrolytic.
L1
D1
1N4148
R LIM
100 Ω
25 μ H
OUTPUT
+3V
1
I LIM
2
V IN
SW1 3
732k Ω
6
7
5
4
2xAA
CELLS
ADP1111
FB 8
AO SET GND SW2 4.7
μ F
+
42.2k Ω
C L
0.1 μ F
1N5818
NC NC
L1 = CTX25-4
1N5818
+
22 μ F
–22V OUTPUT
7mA @ 2V INPUT
Figure 33. 3 V to –22 V LCD Bias Generator
–14 –
0
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| ADP121-ACBZ12R7 | IC REG LDO 1.2V .15A 4WLCSP |
| ADP122AUJZ-2.9-R7 | IC REG LDO 2.9V .3A 5TSOT |
| ADP124ARHZ-2.85-R7 | IC REG LDO 2.85V .5A 8MSOP |
| ADP130AUJZ-2.5-R7 | IC REG LDO 2.5V .35A TSOT-23-5 |
| ADP150AUJZ-2.5-R7 | IC REG LDO 2.5V .15A TSOT-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1111ANZ-3.3 | 功能描述:IC REG BUCK BOOST INV 3.3V 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| ADP1111ANZ-5 | 功能描述:IC REG BUCK BST INV 5V 0.2A 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| ADP1111AR | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin SOIC N 制造商:Analog Devices 功能描述:CONV DC-DC SGL-OUT NON-INV/INV/STEP UP/STEP DOWN 8SOIC N - Rail/Tube 制造商:Analog Devices 功能描述:IC SWITCHING REGULATOR |
| ADP1111AR-12 | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin SOIC N 制造商:Rochester Electronics LLC 功能描述:MICROPOWER STEP-UP/DOWN SWITCHING REG. - Bulk |
| ADP1111AR-12-REEL | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin SOIC N T/R |
发布紧急采购，3分钟左右您将得到回复。