- 您现在的位置：买卖IC网 > PDF目录1776 > ADP1111ANZ-12 (Analog Devices Inc)IC REG BUCK BST INV 12V .2A 8DIP PDF资料下载
参数资料
| 型号： | ADP1111ANZ-12 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/15页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BST INV 12V .2A 8DIP |
| 标准包装： | 50 |
| 类型： | 降压（降压），升压（升压），反相 |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 12V |
| 输入电压： | 2 V ~ 30 V |
| 频率 - 开关： | 72kHz |
| 电流 - 输出： | 200mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 包装： | 管件 |
| 供应商设备封装： | 8-PDIP |
ADP1111
As previously mentioned, the switch voltage is higher in step-
down mode than in step-up mode. V SW is a function of switch
During each switching cycle, the inductor must supply the
following energy:
current and is therefore a function of V IN , L, time and V OUT .
For most applications, a V SW value of 1.5 V is recommended.
The inductor value can now be calculated:
P L
f OSC
=
275 mW
72 kHz
= 3.8 μ J
L =
V IN ( MIN ) ? V SW ? V OUT
I PEAK
? t ON
(Equation 7)
Using a standard inductor value of 56 μ H with 0.2 Ω dc
resistance will produce a peak switch current of:
? 1 ? e
? = 445 mA
where t ON = switch ON time (7 μ s).
If the input voltage will vary (such as an application that must
I PEAK =
4.5 V ? 0.75 V ?
0.65 Ω + 0.2 Ω ?
? 0.85 Ω ? 7 μ s ?
56 μ H
?
operate from a 9 V, 12 V or 15 V source), an R LIM resistor
should be selected from Figure 6. The R LIM resistor will keep
switch current constant as the input voltage rises. Note that
Once the peak current is known, the inductor energy can be
calculated from (Equation 9):
there are separate R LIM values for step-up and step-down modes
of operation.
For example, assume that +5 V at 300 mA is required from a
E L =
1
2
( 56 μ H ) ? ( 445 mA ) 2 = 5.54 μ J
+12 V to +24 V source. Deriving the peak current from
Equation 6 yields:
Since the inductor energy of 5.54 μ J is greater than the P L /f OSC
requirement of 3.82 μ J , the 56 μ H inductor will work in this
? 12 ? 1.5 + 0.5 ? = 600 mA
? ?
I PEAK =
2 ? 300 mA ? 5 + 0.5 ?
0.5
application.
The input voltage only varies between 4.5 V and 5.5 V in this
application. Therefore, the peak current will not change enough
Then, the peak current can be inserted into Equation 7 to
calculate the inductor value:
to require an R LIM resistor and the I LIM pin can be connected
directly to V IN . Care should be taken, of course, to ensure that
the peak current does not exceed 650 mA.
L =
12 ? 1.5 ? 5
600 mA
? 7 μ s = 64 μ H
CAPACITOR SELECTION
P L = ( V + V D ) ? ( I OUT )
Since 64 μH is not a standard value, the next lower standard
value of 56 μ H would be specified.
To avoid exceeding the maximum switch current when the
input voltage is at +24 V, an R LIM resistor should be specified.
Using the step-down curve of Figure 6, a value of 560 Ω will
limit the switch current to 600 mA.
INDUCTOR SELECTION–POSITIVE-TO-NEGATIVE
CONVERTER
The configuration for a positive-to-negative converter using the
ADP1111 is shown in Figure 22. As with the step-up converter,
all of the output power for the inverting circuit must be supplied
by the inductor. The required inductor power is derived from
the formula:
OUT (Equation 8)
The ADP1111 power switch does not saturate in positive-to-
negative mode. The voltage drop across the switch can be
modeled as a 0.75 V base-emitter diode in series with a 0.65 Ω
resistor. When the switch turns on, inductor current will rise at
a rate determined by:
For optimum performance, the ADP1111’s output capacitor
must be selected carefully. Choosing an inappropriate capacitor
can result in low efficiency and/or high output ripple.
Ordinary aluminum electrolytic capacitors are inexpensive but
often have poor Equivalent Series Resistance (ESR) and
Equivalent Series Inductance (ESL). Low ESR aluminum
capacitors, specifically designed for switch mode converter
applications, are also available, and these are a better choice
than general purpose devices. Even better performance can be
achieved with tantalum capacitors, although their cost is higher.
Very low values of ESR can be achieved by using OS-CON
capacitors (Sanyo Corporation, San Diego, CA). These devices
are fairly small, available with tape-and-reel packaging and have
very low ESR.
The effects of capacitor selection on output ripple are demon-
strated in Figures 15, 16 and 17. These figures show the output
of the same ADP1111 converter that was evaluated with three
different output capacitors. In each case, the peak switch
current is 500 mA, and the capacitor value is 100 μ F. Figure 15
shows a Panasonic HF-series 16-volt radial cap. When the
switch turns off, the output voltage jumps by about 90 mV and
then decays as the inductor discharges into the capacitor. The
I L ( ) =
? 1 ? e L ?
t
V L
R '
? ? R ' t ?
? ?
(Equation 9)
rise in voltage indicates an ESR of about 0.18 Ω . In Figure 16,
the aluminum electrolytic has been replaced by a Sprague 293D
series, a 6 V tantalum device. In this case the output jumps
where: R' = 0.65 Ω + R L(DC)
V L = V IN – 0.75 V
For example, assume that a –5 V output at 50 mA is to be
generated from a +4.5 V to +5.5 V source. The power in the
inductor is calculated from Equation 8:
P L = ( | ? 5 V | + 0.5 V | ) ? ( 50 mA ) = 275 mW
–8 –
about 30 mV, which indicates an ESR of 0.06 Ω . Figure 17
shows an OS-CON 16–volt capacitor in the same circuit, and
ESR is only 0.02 Ω .
0
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| ADP121-ACBZ12R7 | IC REG LDO 1.2V .15A 4WLCSP |
| ADP122AUJZ-2.9-R7 | IC REG LDO 2.9V .3A 5TSOT |
| ADP124ARHZ-2.85-R7 | IC REG LDO 2.85V .5A 8MSOP |
| ADP130AUJZ-2.5-R7 | IC REG LDO 2.5V .35A TSOT-23-5 |
| ADP150AUJZ-2.5-R7 | IC REG LDO 2.5V .15A TSOT-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1111ANZ-3.3 | 功能描述:IC REG BUCK BOOST INV 3.3V 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| ADP1111ANZ-5 | 功能描述:IC REG BUCK BST INV 5V 0.2A 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| ADP1111AR | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin SOIC N 制造商:Analog Devices 功能描述:CONV DC-DC SGL-OUT NON-INV/INV/STEP UP/STEP DOWN 8SOIC N - Rail/Tube 制造商:Analog Devices 功能描述:IC SWITCHING REGULATOR |
| ADP1111AR-12 | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin SOIC N 制造商:Rochester Electronics LLC 功能描述:MICROPOWER STEP-UP/DOWN SWITCHING REG. - Bulk |
| ADP1111AR-12-REEL | 制造商:Analog Devices 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2V to 30V 8-Pin SOIC N T/R |
发布紧急采购，3分钟左右您将得到回复。