- 您现在的位置：买卖IC网 > PDF目录17399 > ADP1850SP-EVALZ (Analog Devices Inc)EVAL BOARD FOR ADP1850SP PDF资料下载
参数资料
| 型号： | ADP1850SP-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 26/32页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR ADP1850SP |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.8V，3.3V |
| 电流 - 输出： | 14A，14A |
| 输入电压： | 10 ~ 20 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 600kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ADP1850SP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页
ADP1850
SWITCH NODE
The switch node is the noisiest place in the switcher circuit with
large ac and dc voltages and currents. This node should be wide
to minimize resistive voltage drop. To minimize capacitively
coupled noise, the total area should be small. Place the FETs
and inductor close together on a small copper plane to minimize
series resistance and keep the copper area small.
GATE DRIVER PATHS
Gate drive traces (DH and DL) handle high dI/dt and tend to
produce noise and ringing. They should be as short and direct
as possible. If vias are needed, it is best to use two relatively
Data Sheet
optimal, slowing down the gate drive slightly can be helpful to
reduce noise and ringing. It is occasionally helpful to place
small value resistors, such as between 2 Ω and 4 Ω, on the DHx
and DLx pins. These can be populated with 0 Ω resistors if
resistance is not needed. Note that the added gate resistance
increases the switching rise and fall times, as well as increasing
switching power loss in the MOSFET.
OUTPUT CAPACITORS
The negative terminal of the output filter capacitors should be
tied close to the source of the low side FET. Doing this helps to
minimize voltage differences between AGND and PGNDx.
large ones in parallel to reduce the peak current density and the
current in each via. If the overall PCB layout is less than
Rev. A | Page 26 of 32
相关PDF资料 |
PDF描述 |
|---|---|
| A9BBG-1308F | FLEX CABLE - AFF13G/AF13/AFF13G |
| LQH43CN2R2M03L | INDUCTOR 2.2UH 20% 900MA 1812 |
| RB-3.305D | CONV DC/DC 1W 3.3VIN +/-05VOUT |
| TH3D336K020E0600 | CAP TANT 33UF 20V 10% 2917 |
| IR3316STRRPBF | IC SWITCH HISIDE PROGR D2PAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1851ACPZ-R7 | 功能描述:电流型 PWM 控制器 w-range input Synch StepDown DC/DC Cntr RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ADP1851-EVALZ | 功能描述:电源管理IC开发工具 Evaluation Board 1.8V 25A Output RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| ADP1853 | 制造商:AD 制造商全称:Analog Devices 功能描述:Synchronous, Step-Down DC-to-DC Controller |
| ADP1853ACPZ-R7 | 功能描述:DC/DC 开关控制器 Synch StepDown DC/DC Cntr w/Volt trking RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| ADP1853-EVALZ | 功能描述:电源管理IC开发工具 Evaluation Board 3.3V 20A Output RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。