- 您现在的位置：买卖IC网 > PDF目录16949 > ADP225CP-EVALZ (Analog Devices Inc)BOARD EVAL FOR ADP225 PDF资料下载
参数资料
| 型号： | ADP225CP-EVALZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ADP225 |
| 标准包装： | 1 |
| 系列： | * |
Data Sheet
ADP222/ADP223/ADP224/ADP225
ENABLE FEATURE
The ADP222 / ADP223 / ADP224 / ADP225 use the ENx pins to
enable and disable the VOUTx pins under normal operating
conditions. Figure 67 shows a rising voltage on ENx crossing
the active threshold, where V OUTx turns on. When a falling
voltage on ENx crosses the inactive threshold, V OUTx turns off.
3.5
3.0
2.5
2.0
ENx
3.3V
2.8V
1.8V
1.2V
1.4
1.2
1.0
V IN = 5.5V
1.5
1.0
0.5
0.8
0
0
100
200
300
400
500
600
700
800
900
1000
0.6
0.4
0.2
0
0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
ENABLE VOLTAGE (V)
Figure 67. Typical ENx Pin Operation, V IN = 5.5 V
As shown in Figure 67, the ENx pins have built-in hysteresis.
This prevents on/off oscillations that can occur due to noise on
the ENx pins as it passes through the threshold points.
The active/inactive thresholds of the ENx pins are derived from
the VIN voltage. Therefore, these thresholds vary with changing
input voltage. Figure 68 shows typical ENx active/inactive thresholds
when the input voltage varies from 2.5 V to 5.5 V.
TIME (μs)
Figure 69. Typical Start-Up Time
PARALLELING OUTPUTS TO INCREASE OUTPUT
CURRENT
The ADP223 / ADP225 use a single band gap to generate the
reference voltage for each LDO. The reference voltages are
trimmed to plus or minus a couple of millivolts of each other.
This allows paralleling of the LDOs to increase the output
current to 600 mA. The adjust pins of each LDO are tied
together and a single output voltage divider sets the output
voltage. Even though the output voltage of each LDO is slightly
different, at high load currents, the resistance of the package
and the board layout absorbs the difference. Figure 70 shows
the schematic of a typical application where the LDO outputs
are paralleled.
1.2
1.0
ENx FALL
ENx RISE
V IN = 3.3V
+ C1
1μF
R2
R1
0.8
1 EN1
ADJ1 8
0.6
OFF
ON
2 EN2
VOUT1 7
+ C2
1μF
0.4
3 GND
VIN 6
0.2
4 ADJ2
VOUT2 5
VOUT2 = 2.8V
0
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
Figure 70. Paralleling Outputs for Higher Output Current
V IN (V)
Figure 68. Typical Enable Thresholds vs. Input Voltage
The ADP222 / ADP223 / ADP224 / ADP225 use an internal soft
start to limit the inrush current when the output is enabled. The
start-up time for the 2.8 V option is approximately 240 μs from
the time the ENx active threshold is crossed to when the output
reaches 90% of its final value. The start-up time is somewhat
dependent on the output voltage setting and increases slightly as
the output voltage increases.
QUICK OUTPUT DISCHARGE (QOD) FUNCTION
The ADP224 / ADP225 include an output discharge resistor to
force the voltage on each output to zero when the respective
LDO is disabled. This ensures that the outputs of the LDOs are
always in a well-defined state, regardless if it is enabled or not.
The ADP222 / ADP223 do not include the output discharge
function. Figure 71 compares the turn-off time of a 3.3 V output
LDO with and without the QOD function. Both LDOs have a
1 kΩ resistor connected to each output. The LDO with the
QOD function discharges the output to 0 V in less than 1 ms,
whereas the 1 kΩ load takes over 5 ms to do the same.
Rev. D | Page 19 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| RSM08DRMD-S288 | CONN EDGECARD 16POS .156 EXTEND |
| AD8056ARM-EBZ | BOARD EVAL FOR AD8056ARM |
| LLS2G331MELB | CAP ALUM 330UF 400V 20% SNAP |
| AD8057AR-EBZ | BOARD EVAL FOR AD8057AR |
| RMM08DRMD-S288 | CONN EDGECARD 16POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP2291 | 制造商:AD 制造商全称:Analog Devices 功能描述:Compact, 1.5 A Linear Charger for Single-Cell Li+ Battery |
| ADP2291ACPZ-R7 | 功能描述:IC CHARGER LI-ION 4.2V 8LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| ADP2291ARMZ | 制造商:Analog Devices 功能描述:IC CHARGER 1.5A LI+ SMD MSOP8 制造商:Analog Devices 功能描述:IC, CHARGER, 1.5A LI+, SMD, MSOP8 |
| ADP2291ARMZ-R7 | 功能描述:IC CHARGER LI-ION 4.2V 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| ADP2291-EVAL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。