- 您现在的位置：买卖IC网 > PDF目录4781 > ADP320ACPZ331815R7 (Analog Devices Inc)IC REG LDO 3.3/1.8/1.5V 16LFCSP PDF资料下载
参数资料
| 型号： | ADP320ACPZ331815R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/20页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3/1.8/1.5V 16LFCSP |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V，1.8V，1.5V |
| 输入电压： | 1.8 V ~ 5.5 V |
| 电压 - 压降（标准）： | 0.11V @ 200mA，-，- |
| 稳压器数量： | 3 |
| 电流 - 输出： | 200mA（最小值） |
| 电流 - 限制（最小）： | 250mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 16-LFCSP-WQ（3x3） |
| 包装： | 标准包装 |
| 其它名称： | ADP320ACPZ331815R7DKR |
ADP320
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
VIN1/VIN2, VIN3, VBIAS to GND
VOUT1, VOUT2 to GND
VOUT3 to GND
EN1, EN2, EN3 to GND
Storage Temperature Range
Operating Junction Temperature Range
Soldering Conditions
Rating
–0.3 V to +6.5 V
–0.3 V to VIN1/VIN2
–0.3 V to VIN3
–0.3 V to +6.5 V
–65°C to +150°C
–40°C to +125°C
JEDEC J-STD-020
Junction-to-ambient thermal resistance (θ JA ) of the package is
based on modeling and calculation using a 4-layer board. The
junction-to-ambient thermal resistance is highly dependent
on the application and board layout. In applications where high
maximum power dissipation exists, close attention to thermal
board design is required. The value of θ JA may vary, depending
on PCB material, layout, and environmental conditions. The
specified values of θ JA are based on a four-layer, 4-inch × 3-inch
circuit board. Refer to JEDEC JESD 51-9 for detailed informa-
tion on the board construction. For additional information, see
Stresses above those listed under absolute maximum ratings
may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL DATA
Absolute maximum ratings apply individually only, not in
combination.
The ADP320 triple LDO can be damaged when the junction
temperature limits are exceeded. Monitoring ambient temper-
ature does not guarantee that the junction temperature (T J )
is within the specified temperature limits. In applications
with high power dissipation and poor thermal resistance the
maximum ambient temperature may have to be derated. In
applications with moderate power dissipation and low PCB
thermal resistance, the maximum ambient temperature can
exceed the maximum limit as long as the junction temperature
is within specification limits.
The junction temperature (T J ) of the device is dependent on
the ambient temperature (T A ), the power dissipation of the
device (P D ), and the junction-to-ambient thermal resistance of
the AN-617 Application Note, MicroCSP? Wafer Level Chip
Scale Package .
Ψ JB is the junction to board thermal characterization parameter
with units of °C/W. Ψ JB of the package is based on modeling and
calculation using a 4-layer board. The JESD51-12, Guidelines
for Reporting and Using Package Thermal Information , states
that thermal characterization parameters are not the same as
thermal resistances. Ψ JB measures the component power flowing
through multiple thermal paths rather than a single path as in
thermal resistance, θ JB . Therefore, Ψ JB thermal paths include
convection from the top of the package as well as radiation
from the package; factors that make Ψ JB more useful in real-
world applications. Maximum junction temperature (T J ) is
calculated from the board temperature (T B ) and power
dissipation (P D ) using the following formula
T J = T B + ( P D × Ψ JB )
Refer to JEDEC JESD51-8 and JESD51-12 for more detailed
information about Ψ JB .
THERMAL RESISTANCE
θ JA and Ψ JB are specified for the worst-case conditions, that is, a
device soldered in a circuit board for surface-mount packages.
Table 4.
the package (θ JA ). Maximum junction temperature (T J ) is
calculated from the ambient temperature (T A ) and power dissi-
Package Type
16-Lead 3 mm × 3 mm LFCSP
θ JA
49.5
Ψ JB
25.2
Unit
°C/W
pation (P D ) using the following formula:
T J = T A + ( P D × θ JA )
ESD CAUTION
Rev. A | Page 5 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| EMM28DTKT-S288 | CONN EDGECARD 56POS .156 EXTEND |
| ADP220ACBZ-2812R7 | IC REG LDO 2.8V/1.2V .2A 6WLCSP |
| ADP220ACBZ275275R7 | IC REG LDO 2.75V .2A 6WLCSP |
| ACM18DRMN-S288 | CONN EDGECARD EXTEND 36POS 0.156 |
| ADP220ACBZ-2827R7 | IC REG LDO 2.8V/2.7V .2A 6WLCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP3210 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:7-Bit Programmable Multiphase Mobile CPU Synchronous |
| ADP3210MNR2G | 功能描述:DC/DC 开关控制器 IMVP6.5 BUCK CONTROLLER RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| ADP3211 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:7-Bit, Programmable, Single-Phase, Synchronous Buck Controller |
| ADP32110091MNR2G | 制造商:ON Semiconductor 功能描述:ONSADP32110091MNR2G IMVP6.5 BUCK CONTROL |
| ADP3211AMNR2G | 功能描述:DC/DC 开关控制器 IMVP6.5 BCK CTRL RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。