- 您现在的位置：买卖IC网 > PDF目录19383 > ADSP-21991BBCZ (Analog Devices Inc)IC DSP CTLR 16BIT 196CSPBGA PDF资料下载
参数资料
| 型号： | ADSP-21991BBCZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 42/44页 |
| 文件大小： | 0K |
| 描述： | IC DSP CTLR 16BIT 196CSPBGA |
| 标准包装： | 1 |
| 系列： | ADSP-21xx |
| 类型： | 定点 |
| 接口： | SPI，SSP |
| 时钟速率： | 150MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 112kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 2.50V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 196-BGA |
| 供应商设备封装： | 196-MBGA（15x15） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页
–7–
REV. 0
ADSP-21991
for position sensor feedback; two adjustable frequency auxiliary
PWM outputs, 16 lines of digital I/O; a 16-bit watchdog timer;
three general-purpose timers, and an interrupt controller that
manages all peripheral interrupts. Finally, the ADSP-21991
contains an integrated power-on-reset (POR) circuit that can be
used to generate the required reset signal for device power-on.
The ADSP-21991 has an external memory interface that is
shared by the DSP core, the DMA controller, and DMA capable
peripherals, which include the ADC, SPORT, and SPI commu-
nication ports. The external port consists of a 16-bit data bus, a
20-bit address bus, and control signals. The data bus is config-
urable to provide an 8- or 16-bit interface to external memory.
Support for word packing lets the DSP access 16- or 24-bit words
from external memory regardless of the external data bus width.
The memory DMA controller lets the ADSP-21991 move data
and instructions from between memory spaces: internal-to-
external, internal-to-internal, and external-to- external. On-chip
peripherals can also use this controller for DMA transfers.
The embedded ADSP-219x core can respond to up to seventeen
interrupts at any given time: three internal (stack, emulator
kernel, and power-down), two external (emulator and reset), and
twelve user defined (peripherals) interrupts. Programmers assign
each of the 32 peripheral interrupt requests to one of the 12 user
defined interrupts. These assignments determine the priority of
each peripheral for interrupt service.
The following sections provide a functional overview of the
ADSP-21991 peripherals.
Serial Peripheral Interface (SPI) Port
The Serial Peripheral Interface (SPI) Port provides functionality
for a generic configurable serial port interface based on the SPI
standard, which enables the DSP to communicate with multiple
SPI compatible devices. Key features of the SPI port are:
Interface to host microcontroller or serial EEPROM
Master or slave operation (3-wire interface MISO, MOSI,
SCK)
Data rates to HCLK 4 (16-bit baud rate selector)
8- or 16-bit transfer
Programmable clock phase and polarity
Broadcast Mode – 1 master, multiple slaves
DMA capability and dedicated interrupts
PF0 can be used as slave select input line
PF7–1 can be used as external slave select output
SPI is a 3 wire interface consisting of 2 data pins (MOSI and
MISO), one clock pin (SCK), and a single Slave Select input
(
SPISS) that is multiplexed with the PF0 Flag IO line and seven
Slave Select outputs (SPISEL1 to SPISEL7) that are multiplexed
with the PF1 to PF7 Flag IO lines. The
SPISS input is used to
select the ADSP-21991 as a slave to an external master. The
SPISEL1 to SPISEL7 outputs can be used by the ADSP-21991
(acting as a master) to select/enable up to seven external slaves
in an multi device SPI configuration. In a multimaster or a multi-
device configuration, all MOSI pins are tied together, all MISO
pins are tied together, and all SCK pins are tied together.
During transfers, the SPI port simultaneously transmits and
receives by serially shifting data in and out on the serial data line.
The serial clock line synchronizes the shifting and sampling of
data on the serial data line.
In master mode, the DSP core performs the following sequence
to set up and initiate SPI transfers:
1. Enables and configures the SPI port operation (data size,
and transfer format).
2. Selects the target SPI slave with the SPISELx output pin
(reconfigured Programmable Flag pin).
3. Defines one or more DMA descriptors in Page 0 of I/O
memory space (optional in DMA mode only).
4. Enables the SPI DMA engine and specifies transfer
direction (optional in DMA mode only).
5. In non DMA mode only, reads or writes the SPI port
receive or transmit data buffer.
The SCK line generates the programmed clock pulses for simul-
taneously shifting data out on MOSI and shifting data in on
MISO. In DMA mode only, transfers continue until the SPI
DMA word count transitions from 1 to 0.
In slave mode, the DSP core performs the following sequence to
set up the SPI port to receive data from a master transmitter:
1. Enables and configures the SPI slave port to match the
operation parameters set up on the master (data size and
transfer format) SPI transmitter.
2. Defines and generates a receive DMA descriptor in
Page 0 of memory space to interrupt at the end of the
data transfer (optional in DMA mode only).
3. Enables the SPI DMA engine for a receive access
(optional in DMA mode only).
4. Starts receiving the data on the appropriate SCK edges
after receiving an SPI chip select on the
SPISS input pin
(reconfigured Programmable Flag pin) from a master
In DMA mode only, reception continues until the SPI DMA
word count transitions from 1 to 0. The DSP core could
continue, by queuing up the next DMA descriptor.
A slave mode transmit operation is similar, except the DSP core
specifies the data buffer in memory space from which to transmit
data, generates and relinquishes control of the transmit DMA
descriptor, and begins filling the SPI port data buffer. If the SPI
controller is not ready on time to transmit, it can transmit a “zero”
word.
DSP Serial Port (SPORT)
The ADSP-21991 incorporates a complete synchronous serial
port (SPORT) for serial and multiprocessor communications.
The SPORT supports the following features:
Bidirectional: the SPORT has independent transmit and
receive sections.
Double buffered: the SPORT section (both receive and
transmit) has a data register for transferring data words
to and from other parts of the processor and a register for
shifting data in or out. The double buffering provides
additional time to service the SPORT.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B1V-CV-F3 | CONVERTER MOD DC/DC 5.8V 150W |
| RCM08DTAH-S189 | CONN EDGECARD 16POS R/A .156 SLD |
| VI-2NY-CX-F3 | CONVERTER MOD DC/DC 3.3V 49.5W |
| VI-2NY-CW-F1 | CONVERTER MOD DC/DC 3.3V 66W |
| 1130-332K-RC | CHOKE RF HI CURR 3300UH 10% RAD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-21991BST | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 160MHz 160MIPS 176-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:HIGH PERFORMANCE MIXED SIGNAL DSP - Bulk |
| ADSP-21991BSTZ | 功能描述:IC DSP CONTROLLER 16BIT 176-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:ADSP-21xx 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-21992BBC | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:MIXED SIGNAL DSP W/32K DM RAM& 16K PMRAM - Bulk |
| ADSP-21992BST | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 160MHz 160MIPS 176-Pin LQFP 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
| ADSP-21992BSTZ | 功能描述:IC DSP CONTROLLER 16BIT 176LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:ADSP-21xx 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
发布紧急采购，3分钟左右您将得到回复。