- 您现在的位置：买卖IC网 > PDF目录19468 > ADSP-21992BSTZ (Analog Devices Inc)IC DSP CONTROLLER 16BIT 176LQFP PDF资料下载
参数资料
| 型号： | ADSP-21992BSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/60页 |
| 文件大小： | 0K |
| 描述： | IC DSP CONTROLLER 16BIT 176LQFP |
| 标准包装： | 1 |
| 系列： | ADSP-21xx |
| 类型： | 定点 |
| 接口： | SPI，SSP |
| 时钟速率： | 160MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 128kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 2.50V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 176-LQFP |
| 供应商设备封装： | 176-LQFP（24x24） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Rev. A
|
Page 14 of 60
|
August 2007
ADSP-21992
from an external source using the RESET signal, or alterna-
tively, the internal power-on reset circuit may be used by
connecting the POR pin to the RESET pin. During power-up
the RESET line must be activated for long enough to allow the
DSP core’s internal clock to stabilize. The power-up sequence is
defined as the total time required for the crystal oscillator to sta-
bilize after a valid VDD is applied to the processor and for the
internal phase-locked loop (PLL) to lock onto the specific crys-
tal frequency. A minimum of 512 cycles will ensure that the PLL
has locked (this does not include the crystal oscillator
start-up time).
The RESET input contains some hysteresis. If an RC circuit is
used to generate the RESET signal, the circuit should use an
external Schmitt trigger.
The master reset sets all internal stack pointers to the empty
stack condition, masks all interrupts, and resets all registers to
their default values (where applicable). When RESET is
released, if there is no pending bus request, program control
jumps to the location of the on-chip boot ROM (0xFF0000) and
the booting sequence is performed.
POWER SUPPLIES
The ADSP-21992 has separate power supply connections for the
internal (VDDINT) and external (VDDEXT) power supplies. The
internal supply must meet the 2.5 V requirement. The external
supply must be connected to a 3.3 V supply. All external supply
pins must be connected to the same supply. The ideal power-on
sequence for the DSP is to provide power-up of all supplies
simultaneously. If there is going to be some delay in power-up
between the supplies, provide VDD first, then VDD_IO.
BOOTING MODES
The ADSP-21992 supports a number of different boot modes
that are controlled by the three dedicated hardware boot mode
control pins (BMODE2, BMODE1, and BMODE0). The use of
three boot mode control pins means that up to eight different
boot modes are possible. Of these only five modes are valid on
the ADSP-21992. The ADSP-21992 exposes the boot mecha-
nism to software control by providing a nonmaskable boot
interrupt that vectors to the start of the on-chip ROM memory
block (at address 0xFF0000). A boot interrupt is automatically
initiated following either a hardware initiated reset, via the
RESET pin, or a software initiated reset, via writing to the soft-
ware reset register. Following either a hardware or a software
reset, execution always starts from the boot ROM at address
0xFF0000, irrespective of the settings of the BMODE2,
BMODE1, and BMODE0 pins. The dedicated BMODE2,
BMODE1, and BMODE0 pins are sampled at hardware reset.
The particular boot mode for the ADSP-21992 associated with
the settings of the BMODE2, BMODE1, BMODE0 pins is
defined in Table 3.
Table 3. Summary of Boot Modes
Boot Mode
BMODE2
BMODE1
BMODE0
Function
0
Illegal–Reserved
1
0
1
Boot from External 8-Bit Memory over EMI
2
0
1
0
Execute from External 8-Bit Memory
3
0
1
Execute from External 16-Bit Memory
4
1
0
Boot from SPI
≤ 4K Bits
5
1
0
1
Boot from SPI
> 4K Bits
6
1
0
Illegal–Reserved
7
1
Illegal–Reserved
相关PDF资料 |
PDF描述 |
|---|---|
| HSM36DSEF | CONN EDGECARD 72POS .156 EYELET |
| ADSP-21363BSWZ-1AA | IC DSP 32BIT 333MHZ EPAD 144LQFP |
| MIC184YM | IC SUPERVISOR LOCAL/REMOTE 8SOIC |
| VI-B1N-CW-B1 | CONVERTER MOD DC/DC 18.5V 100W |
| PMEG2005AEV,115 | SCHOTTKY RECT 20V 0.5A SOT666 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-21992YBC | 功能描述:IC DSP CTLR 16BIT 196CSPBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:ADSP-21xx 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-21992YST | 制造商:Analog Devices 功能描述: |
| ADSP-21BT101JST | 制造商:Analog Devices 功能描述: |
| ADSP21CSP01BS200 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADSP21CSP01KS200 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。