- 您现在的位置：买卖IC网 > PDF目录19505 > ADSP-BF527BBCZ-5A (Analog Devices Inc)IC DSP 16BIT 533MHZ 208CSPBGA PDF资料下载
参数资料
| 型号： | ADSP-BF527BBCZ-5A |
| 厂商： | Analog Devices Inc |
| 文件页数： | 76/88页 |
| 文件大小： | 0K |
| 描述： | IC DSP 16BIT 533MHZ 208CSPBGA |
| 产品变化通告： | Datasheet Specification Change 14/Dec/2009 |
| 标准包装： | 1 |
| 系列： | Blackfin® |
| 类型： | 定点 |
| 接口： | DMA，以太网，I²C，PPI，SPI，SPORT，UART，USB |
| 时钟速率： | 533MHz |
| 非易失内存： | ROM（32 kB） |
| 芯片上RAM： | 132kB |
| 电压 - 输入/输出： | 1.8V，2.5V，3.3V |
| 电压 - 核心： | 1.15V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 208-LFBGA，CSPBGA |
| 供应商设备封装： | 208-CSPBGA |
| 包装： | 托盘 |
| 配用： | EVAL-SDP-CB1Z-ND - BOARD EVALUATION FOR SDP-CB1 ADZS-BF527-MPSKIT-ND - BOARD EVAL MEDIA PLAYER BF527 ADZS-BF527-EZLITE-ND - BOARD EVAL ADSP-BF527 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页当前第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
ADSP-BF522/ADSP-BF523/ADSP-BF524/ADSP-BF525/ADSP-BF526/ADSP-BF527
Output Disable Time Measurement
TESTER PIN ELECTRONICS
Output balls are considered to be disabled when they stop driv-
ing, go into a high impedance state, and start to decay from their
output high or low voltage. The output disable time t DIS is the
difference between t DIS_MEASURED and t DECAY as shown on the left
t DIS = t DIS_MEASURED – t DECAY
The time for the voltage on the bus to decay by ΔV is dependent
V LOAD
4pF
50 Ω
70 Ω
50 Ω
2pF
45 Ω
0.5pF
T1
ZO = 50 Ω (impedance)
TD = 4.04 ± 1.18 ns
DUT
OUTPUT
on the capacitive load C L and the load current I L . This decay
time can be approximated by the equation:
t DECAY = ? C L ? V ? ? I L
NOTES:
400 Ω
The time t DECAY is calculated with test loads C L and I L , and with
? V equal to 0.25 V for V DDEXT /V DDMEM (nominal) = 2.5 V/3.3 V
and 0.15 V for V DDEXT /V DDMEM (nominal) = 1.8V.
The time t DIS_MEASURED is the interval from when the reference
signal switches, to when the output voltage decays ΔV from the
measured output high or output low voltage.
Example System Hold Time Calculation
To determine the data output hold time in a particular system,
first calculate t DECAY using the equation given above. Choose ΔV
to be the difference between the processor’s output voltage and
the input threshold for the device requiring the hold time. C L is
the total bus capacitance (per data line), and I L is the total leak-
age or three-state current (per data line). The hold time will be
t DECAY plus the various output disable times as specified in the
THE WORST CASE TRANSMISSION LINE DELAY IS SHOWN AND CAN BE USED
FOR THE OUTPUT TIMING ANALYSIS TO REFELECT THE TRANSMISSION LINE
EFFECT AND MUST BE CONSIDERED. THE TRANSMISSION LINE (TD) IS FOR
LOAD ONLY AND DOES NOT AFFECT THE DATA SHEET TIMING SPECIFICATIONS.
ANALOG DEVICES RECOMMENDS USING THE IBIS MODEL TIMING FOR A GIVEN
SYSTEM REQUIREMENT. IF NECESSARY, A SYSTEM MAY INCORPORATE
EXTERNAL DRIVERS TO COMPENSATE FOR ANY TIMING DIFFERENCES.
Figure 60. Equivalent Device Loading for AC Measurements
(Includes All Fixtures)
12
10
t RISE
8
t FALL
6
4
Capacitive Loading
Output delays and holds are based on standard capacitive loads
of an average of 6 pF on all balls (see Figure 60 ). V LOAD is equal
2
0
t RISE = 1.8V @ 25 °C
t FALL = 1.8V @ 25 °C
to (V DDEXT /V DDMEM ) /2. The graphs of Figure 61 through
0
50
100
150
200
The delay and hold specifications given should be derated by a
factor derived from these figures. The graphs in these figures
may not be linear outside the ranges shown.
LOAD CAPACITANCE (pF)
Figure 61. Driver Type A Typical Rise and Fall Times (10%–90%) vs.
Load Capacitance (1.8V V DDEXT /V DDMEM )
Rev. D
|
Page 76 of 88 | July 2013
相关PDF资料 |
PDF描述 |
|---|---|
| V300A28E400BF3 | CONVERTER MOD DC/DC 28V 400W |
| TPSC335M035R0700 | CAP TANT 3.3UF 35V 20% 2312 |
| HBM15DRUN | CONN EDGECARD 30POS .156 DIP SLD |
| ADSP-BF538BBCZ-5A | IC DSP CTLR 16BIT 316CSPBGA |
| ABM36DSXN | CONN EDGECARD 72POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-BF527BBCZ-5AX | 制造商:Analog Devices 功能描述:DSP 32-Bit 533MHz 208-Pin CSP-BGA |
| ADSP-BF527BBCZ-6A | 功能描述:IC DSP 16BIT 533MHZ 208CSBGA 制造商:analog devices inc. 系列:Blackfin? 包装:托盘 零件状态:有效 类型:定点 接口:DMA，以太网，I2C，PPI，SPI，SPORT，UART，USB 时钟速率:600MHz 非易失性存储器:ROM（32 kB） 片载 RAM:132kB 电压 - I/O:1.8V，2.5V，3.3V 电压 - 内核:1.15V 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:208-FBGA，CSPBGA 供应商器件封装:208-CSPBGA（17x17） 标准包装:1 |
| ADSP-BF527KBCZ-3 | 制造商:Analog Devices 功能描述:- Trays |
| ADSP-BF527KBCZ-5 | 功能描述:IC DSP CTRLR 16B 533MHZ 289BGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF527KBCZ-5AX | 制造商:Analog Devices 功能描述:LOW POWER BLACKFIN PROCESSOR WITH ADVANCED PERIPHERALS - Trays |
发布紧急采购，3分钟左右您将得到回复。