- 您现在的位置：买卖IC网 > PDF目录1900 > ADUC7039BCP6Z-RL (Analog Devices Inc)IC MCU ARM7 BATT SENSER 32LFCSP PDF资料下载
参数资料
| 型号： | ADUC7039BCP6Z-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 83/92页 |
| 文件大小： | 0K |
| 描述： | IC MCU ARM7 BATT SENSER 32LFCSP |
| 标准包装： | 2,500 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 连通性： | LIN，SPI |
| 外围设备： | POR，温度传感器，WDT |
| 输入/输出数： | 6 |
| 程序存储器容量： | 64KB（32K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 数据转换器： | A/D 2x16b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 115°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页当前第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
ADuC7039
Data Sheet
Rev. D | Page 84 of 92
LIN DIAGNOSTIC
The ADuC7039 features a short-circuit protection on the
LIN pin. If a short-circuit condition is detected on the LIN
pin, HVSTA[0] is set. This generates a high voltage interrupt
if enabled in IRQEN[10]. This bit is cleared by re-enabling the
LIN driver using HVCFG[2]. It is possible to disable this feature
through HVCFG[1].
LIN COMMUNICATION
LIN uses frames for data communication. A frame consists of a
header, break, synch, PID issued by the master, and data bytes,
plus checksum generated by a slave as shown in Figure 32. In a
LIN communication, the PID dictates the behavior of the slave:
receive, transmit, or ignore.
Break
The LIN interface of the ADuC7039 automatically detects the
break and sets a flag in the LINSTA register after receiving a
valid break. The minimum length of the break symbol is 11
nominal slave clocks (at 20 kB). The maximum length of a
valid break symbol is programmable and can be configured in
the LINBK MMR. The LIN interface recognizes a valid break
at any time during a LIN communication and flags a collision
(Bit 4 of LINSTA) if the break occurred during an existing
communication.
Synch
The LIN interface automatically detects the synch byte and sets
the baud rate for the subsequent data of the current LIN frame.
This operation is transparent to the user.
PID
The LIN peripheral sees the PID as a data byte. It is available in
the LINDAT MMR. The software must decode the PID. After
reception of the PID stop bit, an interrupt is generated to read
the contents of the LINDAT register before the contents are
overwritten by the next data byte.
Data Bytes
Subsequent data bytes similarly set the interrupt bit to indicate
that a data byte has been received.
In transmit mode, up to 8 data bytes can be transmitted at a
time followed by a checksum.
Checksum
Checksums are automatically calculated as each byte is received
or transmitted with the inverted value being stored in the
LINCS MMR. By default, checksum calculation are per LIN 2.1
specifications, that is, with enhanced checksum calculations
for all frames except the diagnostic frames and reserved frames
where the classic checksum calculation is used. The hardware
automatically recognizes the PID and calculates the checksum
accordingly. There is no requirement for user code to write to
the LINCON register to change the checksum calculation.
To operate in LIN 1.3 mode, user code LIN initialization
routine must set LINCON[7] to 1, to force the hardware in
classic checksum calculation. This register should not be
modified during LIN communication in receive mode.
LIN MMRS
The interface to the LIN block consists of 8 MMRs:
LINCON is a 16-bit control register. This MMR is described
in Table 61. This register should not be accessed during
data reception.
LINDAT is an 8-bit user accessible data register. This
MMR is double-buffered: a shadow register is used to
receive and transmit while user code reads and writes
from/to LINDAT. The LINSTA MMR indicates the
status of the data.
LINSTA is a 16-bit status register. This MMR is described
LINBR is a 19-bit baud rate register. The baud rate is
automatically set by the LIN peripheral and this register
should not be altered by user code. It indicates the number
of core clock ticks during an 8-bit transmission.
LINBK is a 19-bit break timer register controlling the
maximum length of a break symbol to be detected by the
LIN slave interface as valid. The default count is 5500 core
clock ticks. This represents the time taken for 11 bits to be
transmitted at 20 kHz.
LINCS is an 8-bit checksum register. It contains the
inverted result of the current checksum calculation. The
checksum calculation is performed on every byte that is
received or transmitted according to the setting of Bit 4
in LINCON MMR. In transmit mode, the user sets the
bit after the last data to transmit has been written in the
peripheral. The checksum is sent automatically. In receive
mode, the checksum is calculated on receiving each byte,
regardless if this byte is a data byte or the frame checksum.
For example, when receiving a frame with 4 data bytes, the
LINCS MMR contains the expected frame checksum once
the fourth data byte is received. LINCS should contain
0x00 after receiving a correct checksum.
LINLOW is a 19-bit counter clocked at 10 MHz to wake
up the LIN nodes on the bus. The LIN bus is forced low as
long as the LINLOW MMR is greater than 0. For example,
LINLOW = 0x234 generates an 11-bit break at 20 kB.
LINWU is a 19-bit counter clocked by the low power
oscillator. It is used in sleep mode to specify the length
of the low signal that wakes up the device via LIN. For
example, LINWU = 0x13 ignores any breaks of less than
150 s, and the ADuC7039 remains asleep.
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC7061BCPZ32 | IC MCU 16/32BIT 32KB 32LFCSP |
| ADUC7121BBCZ-RL | PRECISION ANALOG MCU I.C |
| ADUC7122BBCZ-RL | PRECISION ANALOG MCU I.C |
| ADUC7126BSTZ126-RL | IC MCU 16/32B 126KB FLASH 80LQFP |
| ADUC7129BSTZ126 | IC DAS MCU ARM7 ADC/DDS 80-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7039WBCPZ | 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Trays 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C. |
| ADUC7039WBCPZ-RL | 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C. |
| ADUC7060 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, Precision Analog Microcontroller, Dual Sigma-Delta ADCs, Flash/EE, ARM7TDMI |
| ADUC7060BCPZ32 | 功能描述:IC MCU 24BIT 32KB FLASH 48LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 产品培训模块:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 标准包装:90 系列:AVR® XMEGA 核心处理器:AVR 芯体尺寸:8/16-位 速度:32MHz 连通性:I²C，IrDA，SPI，UART/USART 外围设备:欠压检测/复位，DMA，POR，PWM，WDT 输入/输出数:50 程序存储器容量:192KB（96K x 16） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 电压 - 电源 (Vcc/Vdd):1.6 V ~ 3.6 V 数据转换器:A/D 16x12b; D/A 2x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:64-TQFP 包装:托盘 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| ADUC7060BCPZ32-RL | 功能描述:IC MCU FLASH 24BIT 32KB 48LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
发布紧急采购，3分钟左右您将得到回复。