- 您现在的位置：买卖IC网 > PDF目录11208 > ADUC7060BCPZ32-RL (Analog Devices Inc)IC MCU FLASH 24BIT 32KB 48LFCSP PDF资料下载
参数资料
| 型号： | ADUC7060BCPZ32-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 25/108页 |
| 文件大小： | 0K |
| 描述： | IC MCU FLASH 24BIT 32KB 48LFCSP |
| 设计资源： | 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145) Low power, Long Range, ISM Wireless Measuring Node (CN0164) |
| 标准包装： | 2,500 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 10MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | POR，PWM，温度传感器，WDT |
| 输入/输出数： | 14 |
| 程序存储器容量： | 32KB（16K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 2.375 V ~ 2.625 V |
| 数据转换器： | A/D 5x24b，8x24b，D/A 1x14b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 48-VFQFN 裸露焊盘，CSP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
Data Sheet
ADuC7060/ADuC7061
Rev. D | Page 23 of 108
By default, after a reset, the Flash/EE memory is logically
mapped to Address 0x00000000. It is possible to logically remap
the SRAM to Address 0x00000000 by setting Bit 0 of the remap
MMR located at 0xFFFF0220. To revert Flash/EE to 0x00000000,
Bit 0 of remap is cleared.
It is sometimes desirable to remap RAM to 0x00000000 to optimize
the interrupt latency of the ADuC706x because code can run in
full 32-bit ARM mode and at maximum core speed. Note that,
when an exception occurs, the core defaults to ARM mode.
Remap Operation
When a reset occurs on the ADuC706x, execution starts automati-
cally in the factory programmed internal configuration code.
This so-called kernel is hidden and cannot be accessed by user
code. If the ADuC706x is in normal mode, it executes the power-
on configuration routine of the kernel and then jumps to the
reset vector, Address 0x00000000, to execute the user’s reset
exception routine. Because the Flash/EE is mirrored at the
bottom of the memory array at reset, the reset routine must
always be written in Flash/EE.
The remap command must be executed from the absolute Flash/EE
address and not from the mirrored, remapped segment of memory,
because this may be replaced by SRAM. If a remap operation is
executed while operating code from the mirrored location, pre-
fetch/data aborts can occur, or the user can observe abnormal
program operation. Any kind of reset logically remaps the Flash/EE
memory to the bottom of the memory array.
Remap Register
Name:
Remap
Address:
0xFFFF0220
Default value: 0x0000
Access:
Read and write
Function:
This 8-bit register allows user code to remap
either RAM or Flash/EE space into the bottom
of the ARM memory space starting at
Address 0x00000000.
Table 12. Remap MMR Bit Designations
Bit
Description
7:1
Reserved. These bits are reserved and should be written
as 0 by user code.
0
Remap bit.
Set by user to remap the SRAM to 0x00000000.
Cleared automatically after reset to remap the Flash/EE
memory to 0x00000000.
FLASH/EE CONTROL INTERFACE
Serial and JTAG programming use the Flash/EE control
interface, which includes the eight MMRs outlined in this
section. Note that the flash page size is 512 bytes.
FEESTA Register
FEESTA is a read-only register that reflects the status of the
flash control interface as described in Table 13.
Name:
FEESTA
Address:
0xFFFF0E00
Default value:
0x0020
Access:
Read
Table 13. FEESTA MMR Bit Designations
Bit
Description
15:6
Reserved.
5
Reserved.
4
Reserved.
3
Flash interrupt status bit. Set automatically when an
interrupt occurs, that is, when a command is complete
and the Flash/EE interrupt enable bit in the FEEMOD
register is set. Cleared when reading the FEESTA
register.
2
Flash/EE controller busy. Set automatically when the
controller is busy. Cleared automatically when the
controller is not busy.
1
Command fail. Set automatically when a command
completes unsuccessfully. Cleared automatically when
reading the FEESTA register.
0
Command pass. Set by the MicroConverter when a
command completes successfully. Cleared
automatically when reading the FEESTA register.
FEEMOD Register
FEEMOD sets the operating mode of the flash control interface.
Table 14 lists FEEMOD MMR bit designations.
Name:
FEEMOD
Address:
0xFFFF0E04
Default value:
0x0000
Access:
Read and write
Table 14. FEEMOD MMR Bit Designations
Bit
Description
15:9
Reserved.
8
Reserved. Always set this bit to 1.
7:5
Reserved. Always set these bits to 0 except when
writing keys.
4
Flash/EE interrupt enable.
Set by user to enable the Flash/EE interrupt. The
interrupt occurs when a command is complete.
Cleared by user to disable the Flash/EE interrupt.
3
Erase/write command protection.
Set by user to enable the erase and write commands.
Cleared to protect the Flash/EE against the erase/write
command.
2:0
Reserved. Always set these bits to 0.
相关PDF资料 |
PDF描述 |
|---|---|
| AD7510DIKQ | IC SWITCH QUAD SPST 16CDIP |
| LX256EV-5FN484I | IC SWITCH DIGITAL 484FPBGA |
| LX256EV-35FN484C | IC SWITCH DIGITAL 484FPBGA |
| LX256V-5FN484C | IC SWITCH DIGITAL 484FPBGA |
| ATSAM3U1CB-CU | IC MCU 64KB CORTEX-M3 100-TFBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7060BSTZ32 | 功能描述:IC MCU FLASH 24BIT 32KB 48LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 产品培训模块:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 标准包装:90 系列:AVR® XMEGA 核心处理器:AVR 芯体尺寸:8/16-位 速度:32MHz 连通性:I²C，IrDA，SPI，UART/USART 外围设备:欠压检测/复位，DMA，POR，PWM，WDT 输入/输出数:50 程序存储器容量:192KB（96K x 16） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 电压 - 电源 (Vcc/Vdd):1.6 V ~ 3.6 V 数据转换器:A/D 16x12b; D/A 2x12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:64-TQFP 包装:托盘 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| ADUC7060BSTZ32-RL | 功能描述:IC ARM7 MCU FLASH 32K 48LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC7061BCPZ32 | 功能描述:IC MCU 16/32BIT 32KB 32LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC7061BCPZ32-RL | 功能描述:IC MCU 16/32BIT 32KB 32LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC70SMARTLINKRL7 | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。