- 您现在的位置：买卖IC网 > Datasheet目录667 > AP034 (Teledyne LeCroy)PROBE ACT DIFFERENTIAL 1GHZ Datasheet资料下载
参数资料
| 型号： | AP034 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 21/60页 |
| 文件大小： | 0K |
| 描述： | PROBE ACT DIFFERENTIAL 1GHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1，20:1 |
| 带宽： | 1GHz |
| 电阻 - 输入： | 1M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 0.85pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Operator’s Manual
NOTE: Probe offset is controlled with the channel OFFSET knob in oscilloscope firmware versions
8.1.0 or higher (including X-Stream firmware). The current offset value is displayed above the
graticule for a few seconds after a change is made by turning the knob. In prior software versions,
the channel OFFSET knob adjusted the offset of the oscilloscope input rather than the probe offset.
When the AP034 Active Differential Probe is used with Teledyne LeCroy oscilloscopes with older
software versions, it is important that the channel offset (controlled by the channel OFFSET knob)
remain set to 0.0000 V. Moving the displayed waveform with the channel offset rather than probe
offset will not re-center the dynamic operating range of the probe. Offsetting the trace with the
oscilloscope channel offset introduces the possibility of erroneous waveforms that result from
overloading the probe.
Autobalance
The AP034 Active Differential Probe incorporates an Autobalance function to remove the DC offset
from the output. Autobalance must be invoked by you. When power is first applied, the probe will
return to the internal values resulting from the last Autobalance cycle. For Autobalance to function
properly, all signals must be removed from the input.
After several minutes of warmup, or when the probe is exposed to a large shift in ambient
temperature, some DC offset drift may occur from thermal effects in the amplifier circuitry. To
initiate an Autobalance cycle, remove the probe from the test circuit and select the AUTOBALANCE
menu selection in the oscilloscope “COUPLING” menu for the channel the probe is connected to. If
the probe is being used with the ADPPS power supply, remove the input signal, then push and hold
both OFFSET buttons for two seconds. The AP034 must be terminated into 50 Ω for successful
Autobalance.
Upon successful completion of the Autobalance cycle, all three of the EFFECTIVE GAIN indicators
will be briefly illuminated. If an input signal is present during auto balance and the routine fails, the
EFFECTIVE GAIN indicators will not illuminate. The probe will then revert to the offset values
resulting from the last. successful completion of the Autobalance cycle. In many situations, this will
be adequate to make routine measurements.
Designing Test Fixtures for the AP034 Probe
Often it is desirable to connect the probe directly to user fabricated test fixtures, such as those
used for semiconductor characterization. To facilitate use with custom test fixtures, the input
receptacles of the AP034 probe are compatible with commercially available 0.025 in. (0.635 mm)
square pins. The receptacles do not require a specific rotational alignment for the square pin. The
dimensions listed below can be used as a layout guide for a test fixture circuit board. The
recommended insertion depth of the pins is 0.100 in. (2.5 mm) to 0.200 in. (5.0 mm).
922261-00 Rev A
15
相关PDF资料 |
PDF描述 |
|---|---|
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
| AS-SYNC | SYNC CBL-ARBSTUDIO WAVEFORM GEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP034-DA10 | 功能描述:DIV BY 10 ATTENUATOR PLUG ON A 制造商:teledyne lecroy 系列:AP 零件状态:有效 类型:测试夹，引线，探针 配件类型:衰减器/分配器 配套使用产品/相关产品:AP034 规格:10 分型 标准包装:1 |
| AP034-W5 | 制造商:Teledyne LeCroy 功能描述:Calibration, Warranties, & Service Plans 5 Year Warranty "including Standard" |
| AP035A101JQT2A | 功能描述:CAP CER 100PF 50V 5% NP0 0603 RoHS:是 类别:电容器 >> 陶瓷 系列:APS 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:- |
| AP035A220JQT2A | 功能描述:CAP CER 22PF 50V 5% NP0 0603 RoHS:是 类别:电容器 >> 陶瓷 系列:APS 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:- |
| AP035C103KQT2A | 功能描述:多层陶瓷电容器MLCC - SMD/SMT 50volts 0.01uF 10% X7R 0603 SIZE RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。