- 您现在的位置：买卖IC网 > Datasheet目录667 > AP034 (Teledyne LeCroy)PROBE ACT DIFFERENTIAL 1GHZ Datasheet资料下载
参数资料
| 型号： | AP034 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 37/60页 |
| 文件大小： | 0K |
| 描述： | PROBE ACT DIFFERENTIAL 1GHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1，20:1 |
| 带宽： | 1GHz |
| 电阻 - 输入： | 1M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 0.85pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Operator’s Manual
second BNC cable from the remaining end of the BNC Tee adapter to the Common Mode Drive
No Termination input connector of the AP033/AP034 Calibration Fixture.
CAUTION : Make sure that the Common Mode Drive No Termination connection is used.
Prolonged application of the power levels used in the low frequency common mode test may
damage the termination resistance in either 50 ohm Termination input of the AP033/AP034
calibration fixture.
4. Set the sine wave generator frequency to 70 Hz, and the output amplitude to 20 V p-p , (4
divisions on the oscilloscope). If necessary, adjust the trigger level for a stable display.
5. Set the oscilloscope to display channel 1, but leave the trigger source set to channel 2. Set the
vertical scale of channel 1 to 2 mV/div. Create a math waveform on channel A defined as the
Average of channel 1. Set the average factor as necessary to reduce noise. Increase the zoom
to a factor of four (0.5 mV/division). Turn off the waveform display of all channels except the A
Math waveform.
6. Increase the zoom of the A Math waveform as needed to measure the peak-to-peak amplitude.
This is the common mode signal.
7. Record the displayed “Common Mode Signal at 70 Hz” to two-digit resolution (x.xx mV) in the
Test Record.
8. Calculate the Common Mode Rejection Ratio (CMRR) at 70 Hz by dividing 20 000 mV by the
measured Common Mode Signal recorded in step C-7 (direct reciprocal of the Common Mode
Gain). Record the result to two-digit resolution (xx 000:1) in the Test Record.
9. Verify that the “Common Mode Rejection Ratio at 70 Hz” is greater than 10 000:1 (80 dB).
10. Change the output amplitude of the Function Generator to approximately 8.0 V p-p , and the
frequency to 1 MHz.
11. Set the oscilloscope to display channel 2 only. Change the horizontal scale factor to 0.5 ? s/div,
and the channel 2 vertical scale to 2 V/div. Turn the BWL on channels 1 and 2 to 200 MHz.
12. Adjust oscilloscope trigger level as necessary for a stable display. Adjust the Function Generator
amplitude as needed to maintain 8.0 V p-p as measured on channel 2.
13. Turn off the oscilloscope channel 2 display, turn on the display of channel 1 and the A Math
waveform (averaged channel 1). Adjust the scale factor of channel 1 and the Zoom of the A
Math waveform as necessary to accurately measure the amplitude of the averaged signal.
14. Record the displayed “Common Mode Signal at 1 MHz” to two-digit resolution in the Test
Record.
922261-00 Rev A
31
相关PDF资料 |
PDF描述 |
|---|---|
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
| AS-SYNC | SYNC CBL-ARBSTUDIO WAVEFORM GEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP034-DA10 | 功能描述:DIV BY 10 ATTENUATOR PLUG ON A 制造商:teledyne lecroy 系列:AP 零件状态:有效 类型:测试夹，引线，探针 配件类型:衰减器/分配器 配套使用产品/相关产品:AP034 规格:10 分型 标准包装:1 |
| AP034-W5 | 制造商:Teledyne LeCroy 功能描述:Calibration, Warranties, & Service Plans 5 Year Warranty "including Standard" |
| AP035A101JQT2A | 功能描述:CAP CER 100PF 50V 5% NP0 0603 RoHS:是 类别:电容器 >> 陶瓷 系列:APS 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:- |
| AP035A220JQT2A | 功能描述:CAP CER 22PF 50V 5% NP0 0603 RoHS:是 类别:电容器 >> 陶瓷 系列:APS 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:- |
| AP035C103KQT2A | 功能描述:多层陶瓷电容器MLCC - SMD/SMT 50volts 0.01uF 10% X7R 0603 SIZE RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。