- 您现在的位置：买卖IC网 > Datasheet目录667 > AP034 (Teledyne LeCroy)PROBE ACT DIFFERENTIAL 1GHZ Datasheet资料下载
参数资料
| 型号： | AP034 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 36/60页 |
| 文件大小： | 0K |
| 描述： | PROBE ACT DIFFERENTIAL 1GHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1，20:1 |
| 带宽： | 1GHz |
| 电阻 - 输入： | 1M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 0.85pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
AP034 Active Differential Probe
10. Move the high frequency sine wave generator output cable from the oscilloscope channel 2
input to the Common Mode Drive 50 ohm Termination connector of the AP033/AP034
Calibration Fixture.
11. Set the high-frequency sine wave generator RF Output to ON.
12. Set the oscilloscope to display channel 1 only, set the trigger source to channel 1, and set the
channel 1 vertical scale factor as needed to measure the amplitude of the displayed waveform.
Adjust the trigger level as necessary for a stable display. This is the common mode signal. Turn
on Math Channel A. Press MATH SETUP, then REDEFINE A. Set the A Math type to Average, Avg
Type to Continuous, with 1:15 weighting, of channel 1. Turn off the trace 1 display.
NOTE : The amplitude of the Common Mode signal should be relatively small. If the output
waveform appears to be a 1 Volt square wave, check that the Common Mode Drive 50 ohm
Termination connector of the AP033/AP034 Calibration Fixture is being used and not the
Differential Drive 50 ohm Termination connector.
13. Measure the peak-to-peak output amplitude of the AP034. Record the reading to two-digit
resolution (xx mV) as “Common Mode Signal at 100 MHz” in the Test Record.
14. Calculate the Common Mode Rejection Ratio (CMRR) at 100 MHz by dividing 2,000 mV by the
measured Common Mode Signal recorded in step B-14 (direct reciprocal of the Common Mode
Gain). Record the result to two-digit resolution (xx:1) in the Test Record.
15. Verify that the CMRR at 100 MHz is greater than 18:1 (25 dB).
16. Turn off the high frequency sine wave generator RF output, and disconnect the output cables.
C. Check Low Frequency CMRR
NOTE: Because greater amplitudes are required to measure the higher CMRR specifications at low
frequencies, the Function Generator will be used in place of the high-frequency sine wave
generator for the low frequency CMRR test.
1. Carefully move the AP034 probe head from the Common Mode Drive 50 ohm Termination
connector of the AP033/AP034 Calibration Fixture to the Common Mode Drive No Termination
connector. Make that sure the probe is fully engaged in the fixture.
2. Set the oscilloscope to display channel 2, the channel 2 input coupling to DC1 M ? , the channel
2 vertical scale to 5 Volt/div, the horizontal scale to 5 ms/div, and the trigger source to channel
2. Set BW limiting on channels 1 and 2 to 25 MHz.
3. Connect the BNC Tee adapter to the output connector of the Function Generator. Connect a
BNC cable from one end of the BNC Tee adapter to channel 2 of the oscilloscope. Connect a
30
922261-00 Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
| AS-SYNC | SYNC CBL-ARBSTUDIO WAVEFORM GEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP034-DA10 | 功能描述:DIV BY 10 ATTENUATOR PLUG ON A 制造商:teledyne lecroy 系列:AP 零件状态:有效 类型:测试夹，引线，探针 配件类型:衰减器/分配器 配套使用产品/相关产品:AP034 规格:10 分型 标准包装:1 |
| AP034-W5 | 制造商:Teledyne LeCroy 功能描述:Calibration, Warranties, & Service Plans 5 Year Warranty "including Standard" |
| AP035A101JQT2A | 功能描述:CAP CER 100PF 50V 5% NP0 0603 RoHS:是 类别:电容器 >> 陶瓷 系列:APS 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:- |
| AP035A220JQT2A | 功能描述:CAP CER 22PF 50V 5% NP0 0603 RoHS:是 类别:电容器 >> 陶瓷 系列:APS 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:- |
| AP035C103KQT2A | 功能描述:多层陶瓷电容器MLCC - SMD/SMT 50volts 0.01uF 10% X7R 0603 SIZE RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。