- 您现在的位置：买卖IC网 > Datasheet目录667 > AP034 (Teledyne LeCroy)PROBE ACT DIFFERENTIAL 1GHZ Datasheet资料下载
参数资料
| 型号： | AP034 |
| 厂商： | Teledyne LeCroy |
| 文件页数： | 24/60页 |
| 文件大小： | 0K |
| 描述： | PROBE ACT DIFFERENTIAL 1GHZ |
| 产品培训模块： | Fundamentals of Probing Overview |
| 标准包装： | 1 |
| 系列： | AP |
| 类型： | 有源差分 |
| 衰减值： | 1:1，10:1，20:1 |
| 带宽： | 1GHz |
| 电阻 - 输入： | 1M |
| 电压 - 最大： | CAT I 42.4V |
| 电容 - 输入： | 0.85pF |
| 线缆长度： | 42.000"（1066.80mm） |
| 颜色： | 灰 |
| 包括： | AC 耦合器，附件工具包，衰减器，外壳，手册 |
| 配用： | MSO 44MXS-B-ND - DGTL O-SCOPE MIX SGL 400MHZ DSO MSO 64MXS-B-ND - DGTL O-SCOPE MIX SGL 600MHZ DSO MSO 104MXS-B-ND - DGTL O-SCOPE MIX SGL 1GHZ DSO WAVESURFER 104MXS-B-ND - DGTL O-SCOPE 1GHZ 5GS/S 4CH WAVESURFER 64MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 4CH WAVESURFER 62MXS-B-ND - DGTL O-SCOPE 600MHZ 5GS/S 2CH WAVESURFER 44MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 4CH WAVESURFER 42MXS-B-ND - DGTL O-SCOPE 400MHZ 5GS/S 2CH WAVESURFER 24MXS-B-ND - DGTL O-SCOPE 200MHZ 2.5GS/S 4CH |
| 相关产品： | PK033-ND - AP033/AP034 ACCES KIT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
AP034 Active Differential Probe
B. Incorrect Frequency Response
Possible causes are a defective probe or oscilloscope, poor connections, or poor grounding.
1. Verify that the BW limiting of the oscilloscope is off.
2. Connect the probe to another oscilloscope. If the probe now measures properly, the problem
may be in the oscilloscope.
3. If the probe behaves as if it is ac-coupled at high frequency, check for an open input
connection.
4. Poor frequency or transient response and AC gain errors may result when one of the two input
connections is open.
5. Exc essive “ring” and other transient problems can result from excessive input lead length. To
test this, shorten the input leads to less than 1 cm. If the transient response changes
significantly, the lead parasitics are the cause.
C. DC Errors
Incorrect DC gain requires recalibration or factory repair. This can be determined by completing the
gain checks in the Performance Verification Procedure.
1. Extremely high source resistance will result in DC gain errors. Check the probe accuracy with
the oscilloscope calibrator signal.
2. Verify that the probe is not being overdriven into clipping for its current gain setting.
3. Excessive offset can result from large changes in ambient temperature. Remove the input
signal from the probe and repeat the Autobalance cycle. With the Offset set to zero, did the
trace return to the center of the graticule?
D. Poor Common Mode Rejection
Use the 1-kHz calibrator signal from the oscilloscope to check common mode rejection. With both
the + input and – input connected to the calibrator signal, a flat line at zero volts should be seen on
the graticule.
1. Check the probe with the plug-on attenuator installed and removed. If excessive common
mode signal appears only when the attenuator is present, the attenuator may need to be
rematched to the probe. Use the procedure listed in this section to match the attenuator.
2. If the common mode signal appears when the probe is connected to the test circuit, but not
when it is attached to the calibrator, the problem may be caused by large mismatches in the
source impedance. Try connecting both inputs to one of the input signals in the test circuit,
then the other. If the common mode signal disappears, try probing lower impedance points
within the circuit.
18
922261-00 Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| AP2S2LC | OSCILLATOR PROG 1.8V +-50PPM SMD |
| AP3S1EJ | OSCILLATOR PROG 2.5V +-20PPM SMD |
| APGDT001 | SYSTEM DEV LIN SERIAL ANALYZER |
| ARE0810KS04 | SWITCH DIP SPST EXTENDED 8POS SM |
| AS-SYNC | SYNC CBL-ARBSTUDIO WAVEFORM GEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AP034-DA10 | 功能描述:DIV BY 10 ATTENUATOR PLUG ON A 制造商:teledyne lecroy 系列:AP 零件状态:有效 类型:测试夹，引线，探针 配件类型:衰减器/分配器 配套使用产品/相关产品:AP034 规格:10 分型 标准包装:1 |
| AP034-W5 | 制造商:Teledyne LeCroy 功能描述:Calibration, Warranties, & Service Plans 5 Year Warranty "including Standard" |
| AP035A101JQT2A | 功能描述:CAP CER 100PF 50V 5% NP0 0603 RoHS:是 类别:电容器 >> 陶瓷 系列:APS 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:- |
| AP035A220JQT2A | 功能描述:CAP CER 22PF 50V 5% NP0 0603 RoHS:是 类别:电容器 >> 陶瓷 系列:APS 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装，MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805（2012 公制） 尺寸/尺寸:0.079" L x 0.047" W（2.00mm x 1.20mm） 高度 - 座高（最大）:- 厚度（最大）:- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:- |
| AP035C103KQT2A | 功能描述:多层陶瓷电容器MLCC - SMD/SMT 50volts 0.01uF 10% X7R 0603 SIZE RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。