收藏本站
参数资料
型号： APA300-PQG208I
厂商： Microsemi SoC
文件页数： 162/178页
文件大小： 0K
描述： IC FPGA PROASIC+ 300K 208-PQFP
标准包装： 24
系列： ProASICPLUS
RAM 位总计： 73728
输入/输出数： 158
门数： 300000
电源电压： 2.3 V ~ 2.7 V
安装类型： 表面贴装
工作温度： -40°C ~ 85°C
封装/外壳： 208-BFQFP
供应商设备封装： 208-PQFP（28x28）
ProASICPLUS Flash Family FPGAs
2- 74
v5.9
VPP
Programming Supply Pin
This pin may be connected to any voltage between GND
and 16.5 V during normal operation, or it can be left
unconnected.2 For information on using this pin during
programming,
see
the
In-System
Programming
ProASICPLUS Devices application note. Actel recommends
floating the pin or connecting it to VDDP.
VPN
Programming Supply Pin
This pin may be connected to any voltage between 0.5 V
and –13.8 V during normal operation, or it can be left
unconnected.3 For information on using this pin during
programming,
see
the
In-System
Programming
ProASICPLUS Devices application note. Actel recommends
floating the pin or connecting it to GND.
Recommended Design Practice
for VPN/VPP
ProASICPLUS Devices – APA450, APA600,
APA750, APA1000
Bypass capacitors are required from VPP to GND and VPN
to GND for all ProASICPLUS devices during programming.
During the erase cycle, ProASICPLUS devices may have
current surges on the VPP and VPN power supplies. The
only way to maintain the integrity of the power
distribution to the ProASICPLUS device during these
current surges is to counteract the inductance of the
finite length conductors that distribute the power to the
device. This can be accomplished by providing sufficient
bypass capacitance between the VPP and VPN pins and
GND (using the shortest paths possible). Without
sufficient
bypass
capacitance
to
counteract
the
inductance, the VPP and VPN pins may incur a voltage
spike beyond the voltage that the device can withstand.
This issue applies to all programming configurations.
The solution prevents spikes from damaging the
ProASICPLUS devices. Bypass capacitors are required for
the VPP and VPN pads. Use a 0.01 F to 0.1 F ceramic
capacitor with a 25 V or greater rating. To filter low-
frequency noise (decoupling), use a 4.7 F (low ESR, <1
<
Ω, tantalum, 25 V or greater rating) capacitor. The
capacitors should be located as close to the device pins as
possible (within 2.5 cm is desirable). The smaller, high-
frequency capacitor should be placed closer to the device
pins than the larger low-frequency capacitor. The same
dual-capacitor circuit should be used on both the VPP and
VPN pins (Figure 2-46).
ProASICPLUS Devices – APA075, APA150,
APA300
These devices do not require bypass capacitors on the VPP
and VPN pins as long as the total combined distance of
the programming cable and the trace length on the
board is less than or equal to 30 inches. Note: For trace
lengths greater than 30 inches, use the bypass capacitor
recommendations in the previous section.
2. There is a nominal 40 k
Ω pull-up resistor on V
PP.
3. There is a nominal 40 k
Ω pull-down resistor on V
PN.
Figure 2-46 ProASICPLUS VPP and VPN Capacitor Requirements
2.5cm
0.1 F
to
0.01 F
Programming
Header
or
Supplies
4.7 F
Actel
ProASIC
Device
+
_
V
PP
V
PN
+
_
0.1 F
to
0.01 F
4.7 F
PLUS
相关PDF资料
PDF描述
GEC43DTEN CONN EDGECARD 86POS .100 EYELET
GEC43DTEH CONN EDGECARD 86POS .100 EYELET
ACC50DRTN CONN EDGECARD 100PS .100 DIP SLD
ACC65DRTF CONN EDGECARD 130PS .100 DIP SLD
RSA50DTKI-S288 CONN EDGECARD 100PS .125 EXTEND
相关代理商/技术参数
参数描述
APA300-PQG208M 制造商:Microsemi Corporation 功能描述:FPGA PROASICPLUS 300K GATES 180MHZ 0.22UM 2.5V 208PQFP - Trays
APA300-PQGB 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
APA300-PQGES 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
APA300-PQGI 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
APA300-PQGM 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:ProASIC Flash Family FPGAs
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*