- 您现在的位置：买卖IC网 > PDF目录17274 > AS5040 DB V2 (ams)BOARD DEMO AS5040 PDF资料下载
参数资料
| 型号： | AS5040 DB V2 |
| 厂商： | ams |
| 文件页数： | 21/34页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO AS5040 |
| 标准包装： | 1 |
| 传感器类型： | 磁性，旋转位置 |
| 传感范围： | 360° |
| 接口： | USB |
| 电源电压： | 5V USB 或 9V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板，线缆 |
| 已用 IC / 零件： | AS5040 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
AS5040
Data Sheet
Repeated OTP Programming
Although a single AS5040 OTP register bit can be programmed only once (from 0 to 1), it is possible to program other,
unprogrammed bits in subsequent programming cycles. However, a bit that has already been programmed should not
be programmed twice. Therefore it is recommended that bits that are already programmed are set to “0” during a
programming cycle.
Non-permanent Programming
It is also possible to re-configure the AS5040 in a non-permanent way by overwriting the OTP register.
This procedure is essentially a “Write Data” sequence (see Figure 14) without a subsequent OTP programming cycle.
The “Write Data” sequence may be applied at any time during normal operation. This configuration remains set while
the power supply voltage is above the power-on reset level (see 0).
See Application Note AN5000-20 for further information.
Analog Readback Mode
Non-volatile programming (OTP) uses on-chip zener diodes, which become permanently low resistive when subjected
to a specified reverse current.
The quality of the programming process depends on the amount of current that is applied during the programming
process (up to 130mA). This current must be provided by an external voltage source. If this voltage source cannot
provide adequate power, the zener diodes may not be programmed properly.
In order to verify the quality of the programmed bits, an analog level can be read for each zener diode, giving an
indication whether this particular bit was properly programmed or not.
To put the AS5040 in analog readback mode, a digital sequence must be applied to pins CSn, Prog and CLK as
shown in Figure 17. The digital level for this pin depends on the supply configuration (3.3V or 5V; see section 14).
The second rising edge on CSn (OutpEN) changes pin Prog to a digital output and the log. high signal at pin Prog
must be removed to avoid collision of outputs (grey area in Figure 17).
The following falling slope of CSn changes pin Prog to an analog output, providing a reference voltage V ref , that must
be saved as a reference for the calculation of the subsequent programmed and unprogrammed OTP bits.
Following this step, each rising slope of CLK outputs one bit of data in the reverse order as during programming.
(see Figure 17: Md0-MD1-Div0,Div1-Indx-Z0…Z9, ccw)
During analog readback, the capacitor at pin Prog (see Figure 16) should be removed to allow a fast readout rate. . If
the capacitor is not removed the analog voltage will take longer to stabilize due to the additional capacitance.
The measured analog voltage for each bit must be subtracted from the previously measured V ref , and the resulting
value gives an indication on the quality of the programmed bit: a reading of <100mV indicates a properly programmed
bit and a reading of >1V indicates a properly unprogrammed bit.
A reading between 100mV and 1V indicates a faulty bit, which may result in an undefined digital value, when the OTP
is read at power-up.
Following the 16 th clock (after reading bit “ccw”), the chip must be reset by disconnecting the power supply.
Figure 17: OTP Register Analog Read
P ro g E N
O u tp E N
A n a lo g R e a d b a c k D a ta a t P ro g
P o w e r-o n -
R e se t;
CSn
In te rn a l
V re f
V p ro g ra m m e d
tu rn o ff
s u p p ly
P ro g
te s t b it
d ig ita l
M d 0 M d 1 D iv 0 D iv1 V u n p ro g ra m m e d Z 5
Z6
Z7
Z8
Z9
ccw
P ro g c h a n g e s to O u tp u t
CLK
t L o a d P ro g
1
C L K A re a d
16
www.austriamicrosystems.com
Revision 2.10
20 - 33
相关PDF资料 |
PDF描述 |
|---|---|
| EEC22DREI | CONN EDGECARD 44POS .100 EYELET |
| MAX15035EVKIT+ | EVALUATION KIT FOR MAX15035 |
| 592D336X0010D2W15H | CAP TANT 33UF 10V 20% 2917 |
| L-14CR22JV4T | CER INDUCTOR 220NH 0603 |
| ECC20DCSN | CONN EDGECARD 40POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5040-PB | 功能描述:磁传感器开发工具 AS5040 Progamming Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压: |
| AS5040-SS_EK_AB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5040 标准包装:1 |
| AS5040-SS_EK_DB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5040 标准包装:1 |
| AS5040-SS_EK_PB | 功能描述:AS5000 Programmer, AS5040 - ZIF Socket 制造商:ams 系列:- 零件状态:有效 模块/板类型:ZIF 插口 配套使用产品/相关产品:AS5000 编程器，AS5040 标准包装:1 |
| AS-5041 | 制造商:Bud Industries Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。