- 您现在的位置：买卖IC网 > PDF目录17274 > AS5040 DB V2 (ams)BOARD DEMO AS5040 PDF资料下载
参数资料
| 型号： | AS5040 DB V2 |
| 厂商： | ams |
| 文件页数： | 22/34页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO AS5040 |
| 标准包装： | 1 |
| 传感器类型： | 磁性，旋转位置 |
| 传感范围： | 360° |
| 接口： | USB |
| 电源电压： | 5V USB 或 9V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板，线缆 |
| 已用 IC / 零件： | AS5040 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
AS5040
Data Sheet
13 Alignment Mode
The alignment mode simplifies centering the magnet over the chip to gain maximum accuracy and XY-alignment
tolerance.
This electrical centering method allows a wider XY-alignment tolerance (0.485mm radius) than mechanical centering
(0.25mm radius) as it eliminates the placement tolerance of the die within the IC package (+/- 0.235mm).
Alignment mode can be enabled with the falling edge of CSn while Prog = logic high (Figure 18). The Data bits D9-D0
of the SSI change to a 10-bit displacement amplitude output. A high value indicates large X or Y displacement, but
also higher absolute magnetic field strength. The magnet is properly aligned, when the difference between highest
and lowest value over one full turn is at a minimum.
Under normal conditions, a properly aligned magnet will result in a reading of less than 32 over a full turn.
The MagINCn and MagDECn indicators will be = 1 when the alignment mode reading is < 32. At the same time, both
hardware pins MagINCn (#1) and MagDECn (#2) will be pulled to VSS. A properly aligned magnet will therefore
produce a MagINCn = MagDECn = 1 signal throughout a full 360° turn of the magnet.
Stronger magnets or short gaps between magnet and IC may show values larger than 32. These magnets are still
properly aligned as long as the difference between highest and lowest value over one full turn is at a minimum.
The alignment mode can be reset to normal operation mode by a power-on-reset (disconnect / re-connect power
supply).
Figure 18: Enabling the Alignment Mode
Prog
CSn
AlignMode enable
Read-out
via SSI
2μs 2μs
min. min.
14 3.3V / 5V Operation
The AS5040 operates either at 3.3V ±10% or at 5V ±10%. This is made possible by an internal 3.3V Low-Dropout
(LDO) voltage regulator. The internal supply voltage is always taken from the output of the LDO, meaning that the
internal blocks are always operating at 3.3V.
For 3.3V operation, the LDO must be bypassed by connecting VDD3V3 with VDD5V (see Figure 19).
For 5V operation, the 5V supply is connected to pin VDD5V, while VDD3V3 (LDO output) must be buffered by a
2.2...10μF capacitor, which is supposed to be placed close to the supply pin (see Figure 19).
The VDD3V3 output is intended for internal use only It must not be loaded with an external load.
The output voltage of the digital interface I/O’s corresponds to the voltage at pin VDD5V, as the I/O buffers are
supplied from this pin (see Figure 19).
www.austriamicrosystems.com
Revision 2.10
21 - 33
相关PDF资料 |
PDF描述 |
|---|---|
| EEC22DREI | CONN EDGECARD 44POS .100 EYELET |
| MAX15035EVKIT+ | EVALUATION KIT FOR MAX15035 |
| 592D336X0010D2W15H | CAP TANT 33UF 10V 20% 2917 |
| L-14CR22JV4T | CER INDUCTOR 220NH 0603 |
| ECC20DCSN | CONN EDGECARD 40POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5040-PB | 功能描述:磁传感器开发工具 AS5040 Progamming Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压: |
| AS5040-SS_EK_AB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5040 标准包装:1 |
| AS5040-SS_EK_DB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5040 标准包装:1 |
| AS5040-SS_EK_PB | 功能描述:AS5000 Programmer, AS5040 - ZIF Socket 制造商:ams 系列:- 零件状态:有效 模块/板类型:ZIF 插口 配套使用产品/相关产品:AS5000 编程器，AS5040 标准包装:1 |
| AS-5041 | 制造商:Bud Industries Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。