- 您现在的位置：买卖IC网 > Datasheet目录313 > AT28BV256-20SU (Atmel)IC EEPROM 256KBIT 200NS 28SOIC Datasheet资料下载
参数资料
| 型号： | AT28BV256-20SU |
| 厂商： | Atmel |
| 文件页数： | 5/17页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 256KBIT 200NS 28SOIC |
| 标准包装： | 27 |
| 格式 - 存储器： | EEPROMs - 并行 |
| 存储器类型： | EEPROM |
| 存储容量： | 256K (32K x 8) |
| 速度： | 200ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 产品目录页面： | 1458 (CN2011-ZH PDF) |
AT28BV256
5.6.1
5.6.2
5.7
Hardware Protection
Hardware features protect against inadvertent writes to the AT28BV256 in the following ways:
(a) V CC power-on delay – once V CC has reached 1.8V (typical) the device will automatically time
out 10 ms (typical) before allowing a write; (b) write inhibit – holding any one of OE low, CE high
or WE high inhibits write cycles; and (c) noise filter – pulses of less than 15 ns (typical) on the
WE or CE inputs will not initiate a write cycle.
Software Data Protection
A software-controlled data protection feature has been implemented on the AT28BV256. Soft-
ware data protection (SDP) helps prevent inadvertent writes from corrupting the data in the
device. SDP can prevent inadvertent writes during power-up and power-down as well as any
other potential periods of system instability.
The AT28BV256 can only be written using the software data protection feature. A series of three
write commands to specific addresses with specific data must be presented to the device before
writing in the byte or page mode. The same three write commands must begin each write opera-
tion. All software write commands must obey the page mode write timing specifications. The
data in the 3-byte command sequence is not written to the device; the address in the command
sequence can be utilized just like any other location in the device.
Any attempt to write to the device without the 3-byte sequence will start the internal write timers.
No data will be written to the device; however, for the duration of t WC , read operations will effec-
tively be polling operations.
Device Identification
An extra 64 bytes of EEPROM memory are available to the user for device identification. By rais-
ing A9 to 12V ± 0.5V and using address locations 7FC0H to 7FFFH the additional bytes may be
written to or read from in the same manner as the regular memory array.
5
0273K–PEEPR–2/09
相关PDF资料 |
PDF描述 |
|---|---|
| AT28BV64-30TI | IC EEPROM 64KBIT 300NS 28TSOP |
| AT28C010E-20TI | IC EEPROM 1MBIT 200NS 32TSOP |
| AT28C16E-15SC | IC EEPROM 16KBIT 150NS 24SOIC |
| AT28C17E-15SI | IC EEPROM 16KBIT 150NS 28SOIC |
| AT28C256E-15TI | IC EEPROM 256KBIT 150NS 28TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT28BV256-20SU SL383 | 制造商:Atmel Corporation 功能描述:EEPROM PARALLEL 256KBIT 32KX8 3.3V 28SOIC - Tape and Reel |
| AT28BV256-20SU-T | 功能描述:200NS, SOIC, IND TEMP, GREEN 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:在售 存储器类型:非易失 存储器格式:EEPROM 技术:EEPROM 存储容量:256Kb （32K x 8） 写周期时间 - 字，页:10ms 访问时间:200ns 存储器接口:并联 电压 - 电源:2.7 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TC） 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商器件封装:28-SOIC 标准包装:1 |
| AT28BV256-20TA | 功能描述:IC EEPROM 256KBIT 200NS 28TSOP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:378 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:8M（1M x 8，512K x 16） 速度:110ns 接口:并联 电源电压:2.7 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-CBGA 供应商设备封装:48-CBGA（7x7） 包装:托盘 |
| AT28BV256-20TC | 功能描述:电可擦除可编程只读存储器 256K 2.7V - 3.6V SDP-200NS COM TEMP RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| AT28BV256-20TI | 功能描述:电可擦除可编程只读存储器 256K 2.7V - 3.6V SDP- 200NS IND TEMP RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。