参数资料
型号: AT45DB011B-XU
厂商: Atmel
文件页数: 6/32页
文件大小: 0K
描述: IC FLASH 1MBIT 20MHZ 14TSSOP
标准包装: 96
格式 - 存储器: 闪存
存储器类型: DataFLASH
存储容量: 1M(512 页 x 264 字节)
速度: 20MHz
接口: SPI 3 线串行
电源电压: 2.7 V ~ 3.6 V
工作温度: -40°C ~ 85°C
封装/外壳: 14-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 14-TSSOP
包装: 管件
BUFFER TO MAIN MEMORY PAGE PROGRAM WITHOUT BUILT-IN ERASE: A previously
erased page within main memory can be programmed with the contents of the buffer. An 8-bit
opcode of 88H is followed by the six reserved bits, nine address bits (PA8-PA0) that specify
the page in the main memory to be written, and nine additional don’t care bits. When a low-to-
high transition occurs on the CS pin, the part will program the data stored in the buffer into the
specified page in the main memory. It is necessary that the page in main memory that is being
programmed has been previously erased. The programming of the page is internally self-
timed and should take place in a maximum time of t P . During this time, the status register will
indicate that the part is busy.
Successive page programming operations without doing a page erase are not recommended.
In other words, changing bytes within a page from a “1” to a “0” during multiple page program-
ming operations without erasing that page is not recommended.
PAGE ERASE: The optional Page Erase command can be used to individually erase any
page in the main memory array allowing the Buffer to Main Memory Page Program without
Built-in Erase command to be utilized at a later time. To perform a Page Erase, an opcode of
81H must be loaded into the device, followed by six reserved bits, nine address bits (PA8 -
PA0), and nine don’t care bits. The nine address bits are used to specify which page of the
memory array is to be erased. When a low-to-high transition occurs on the CS pin, the part will
erase the selected page to 1s. The erase operation is internally self-timed and should take
place in a maximum time of t PE . During this time, the status register will indicate that the part is
busy.
BLOCK ERASE: A block of eight pages can be erased at one time allowing the Buffer to Main
Memory Page Program without Built-in Erase command to be utilized to reduce programming
times when writing large amounts of data to the device. To perform a Block Erase, an opcode
of 50H must be loaded into the device, followed by six reserved bits, six address bits (PA8-
PA3), and 12 don’t care bits. The six address bits are used to specify which block of eight
pages is to be erased. When a low-to-high transition occurs on the CS pin, the part will erase
the selected block of eight pages to 1s. The erase operation is internally self-timed and should
take place in a maximum time of t BE . During this time, the status register will indicate that the
part is busy.
Block Erase Addressing
PA8
0
0
0
0
?
?
?
1
1
1
1
PA7
0
0
0
0
?
?
?
1
1
1
1
PA6
0
0
0
0
?
?
?
1
1
1
1
PA5
0
0
0
0
?
?
?
1
1
1
1
PA4
0
0
1
1
?
?
?
0
0
1
1
PA3
0
1
0
1
?
?
?
0
1
0
1
PA2
X
X
X
X
?
?
?
X
X
X
X
PA1
X
X
X
X
?
?
?
X
X
X
X
PA0
X
X
X
X
?
?
?
X
X
X
X
Block
0
1
2
3
?
?
?
60
61
62
63
6
AT45DB011B
1984J–DFLASH–06/06
相关PDF资料
PDF描述
AISM-1812-680K-T INDUCTOR CHIP 68UH 130MA SMD
T95Y476K6R3CSAL CAP TANT 47UF 6.3V 10% 2910
IXDN409SI IC MOSFET DRVR 9A LOSIDE 8-SOIC
SDR0403-330KL INDUCTOR POWER 33UH 0.64A 0403
395-072-541-204 CARD EDGE 72POS DL .100X.200 BLK
相关代理商/技术参数
参数描述
AT45DB011D 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:1-megabit 2.7-volt Minimum DataFlash
AT45DB011D_07 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:1-megabit 2.7-volt DataFlash
AT45DB011D_08 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:1-megabit 2.7-volt Minimum DataFlash
AT45DB011D_09 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:1-megabit 2.7-volt Minimum DataFlash
AT45DB011D-DWF 制造商:Adesto Technologies Corporation 功能描述:1M DATAFLASH, 8-UDFN,IND,GRN,NIPDAU - 1MB, DATAFLASH, WAFER, - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:Adesto Technologies Corporation 功能描述:DIE/WAFER FLASH 1MBIT 66MHZ