- 您现在的位置：买卖IC网 > PDF目录20437 > AT45DB081B-TU (Atmel)IC FLASH 8MBIT 20MHZ 28TSOP PDF资料下载
参数资料
| 型号： | AT45DB081B-TU |
| 厂商： | Atmel |
| 文件页数： | 6/33页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 8MBIT 20MHZ 28TSOP |
| 标准包装： | 234 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | DataFLASH |
| 存储容量： | 8M（4096 页 x 264 字节） |
| 速度： | 20MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-TSSOP（0.465"，11.8mm 宽） |
| 供应商设备封装： | 28-TSOP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Successive page programming operations without doing a page erase are not recommended. In
other words, changing bytes within a page from a “1” to a “0” during multiple page programming
operations without erasing that page is not recommended.
PAGE ERASE: The optional Page Erase command can be used to individually erase any page
in the main memory array allowing the Buffer to Main Memory Page Program without Built-in
Erase command to be utilized at a later time. To perform a Page Erase, an opcode of 81H must
be loaded into the device, followed by three reserved bits, 12 address bits (PA11 - PA0), and
nine don’t care bits. The 12 address bits are used to specify which page of the memory array is
to be erased. When a low-to-high transition occurs on the CS pin, the part will erase the selected
page to 1s. The erase operation is internally self-timed and should take place in a maximum time
of t PE . During this time, the status register will indicate that the part is busy.
BLOCK ERASE: A block of eight pages can be erased at one time allowing the Buffer to Main
Memory Page Program without Built-in Erase command to be utilized to reduce programming
times when writing large amounts of data to the device. To perform a Block Erase, an opcode of
50H must be loaded into the device, followed by three reserved bits, nine address bits (PA11 -
PA3), and 12 don’t care bits. The nine address bits are used to specify which block of eight
pages is to be erased. When a low-to-high transition occurs on the CS pin, the part will erase the
selected block of eight pages to 1s. The erase operation is internally self-timed and should take
place in a maximum time of t BE . During this time, the status register will indicate that the part is
busy.
Block Erase Addressing
PA11
0
0
0
0
?
?
?
1
1
1
1
PA10
0
0
0
0
?
?
?
1
1
1
1
PA9
0
0
0
0
?
?
?
1
1
1
1
PA8
0
0
0
0
?
?
?
1
1
1
1
PA7
0
0
0
0
?
?
?
1
1
1
1
PA6
0
0
0
0
?
?
?
1
1
1
1
PA5
0
0
0
0
?
?
?
1
1
1
1
PA4
0
0
1
1
?
?
?
0
0
1
1
PA3
0
1
0
1
?
?
?
0
1
0
1
PA2
X
X
X
X
?
?
?
X
X
X
X
PA1
X
X
X
X
?
?
?
X
X
X
X
PA0
X
X
X
X
?
?
?
X
X
X
X
Block
0
1
2
3
?
?
?
508
509
510
511
MAIN MEMORY PAGE PROGRAM THROUGH BUFFER: This operation is a combination of the
Buffer Write and Buffer to Main Memory Page Program with Built-in Erase operations. Data is
first shifted into buffer 1 or buffer 2 from the SI pin and then programmed into a specified page in
the main memory. To initiate the operation, an 8-bit opcode, 82H for buffer 1 or 85H for buffer 2,
must be followed by the three reserved bits and 21 address bits. The 12 most significant address
bits (PA11 - PA0) select the page in the main memory where data is to be written, and the next
nine address bits (BFA8 - BFA0) select the first byte in the buffer to be written. After all address
bits are shifted in, the part will take data from the SI pin and store it in one of the data buffers. If
the end of the buffer is reached, the device will wrap around back to the beginning of the buffer.
When there is a low-to-high transition on the CS pin, the part will first erase the selected page in
main memory to all 1s and then program the data stored in the buffer into the specified page in
the main memory. Both the erase and the programming of the page are internally self-timed and
6
AT45DB081B
2225J–DFLSH–2/08
相关PDF资料 |
PDF描述 |
|---|---|
| T95D277K004CZAS | CAP TANT 270UF 4V 10% 2917 |
| 395-072-527-204 | CARD EDGE 72POS DL .100X.200 BLK |
| ASPI-0412S-1R2N-T3 | INDUCTOR POWER MINI 1.2UH 0412 |
| T95D157M016EZSL | CAP TANT 150UF 16V 20% 2917 |
| 395-072-527-202 | CARD EDGE 72POS DL .100X.200 BLK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT45DB081D | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash |
| AT45DB081D_07 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash |
| AT45DB081D_08 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash |
| AT45DB081D_09 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash |
| AT45DB081D_13 | 制造商:AD 制造商全称:Analog Devices 功能描述:8-megabit 2.5V or 2.7V DataFlash |
发布紧急采购，3分钟左右您将得到回复。