- 您现在的位置：买卖IC网 > PDF目录20437 > AT45DB081B-TU (Atmel)IC FLASH 8MBIT 20MHZ 28TSOP PDF资料下载
参数资料
| 型号： | AT45DB081B-TU |
| 厂商： | Atmel |
| 文件页数： | 8/33页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 8MBIT 20MHZ 28TSOP |
| 标准包装： | 234 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | DataFLASH |
| 存储容量： | 8M（4096 页 x 264 字节） |
| 速度： | 20MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-TSSOP（0.465"，11.8mm 宽） |
| 供应商设备封装： | 28-TSOP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
If a sector is programmed or reprogrammed sequentially page-by-page, then the programming
algorithm shown in <blue>Figure 1 on <blue>page 26 is recommended. Otherwise, if multiple
bytes in a page or several pages are programmed randomly in a sector, then the programming
algorithm shown in <blue>Figure 2 on <blue>page 27 is recommended. Each page within a sec-
tor must be updated/rewritten at least once within every 10,000 cumulative page erase/program
operations in that sector.
Operation Mode
Summary
Pin Descriptions
The modes described can be separated into two groups – modes which make use of the Flash
memory array (Group A) and modes which do not make use of the Flash memory array (Group
B).
Group A modes consist of:
1. Main Memory Page Read
2. Main Memory Page to Buffer 1 (or 2) Transfer
3. Main Memory Page to Buffer 1 (or 2) Compare
4. Buffer 1 (or 2) to Main Memory Page Program with Built-in Erase
5. Buffer 1 (or 2) to Main Memory Page Program without Built-in Erase
6. Page Erase
7. Block Erase
8. Main Memory Page Program through Buffer
9. Auto Page Rewrite
Group B modes consist of:
1. Buffer 1 (or 2) Read
2. Buffer 1 (or 2) Write
3. Status Register Read
If a Group A mode is in progress (not fully completed) then another mode in Group A should not
be started. However, during this time in which a Group A mode is in progress, modes in Group B
can be started.
This gives the Serial DataFlash the ability to virtually accommodate a continuous data stream.
While data is being programmed into main memory from buffer 1, data can be loaded into buffer
2 (or vice versa). See application note AN-4 (“Using Atmel’s Serial DataFlash”) for more details.
SERIAL INPUT (SI): The SI pin is an input-only pin and is used to shift data into the device. The
SI pin is used for all data input including opcodes and address sequences.
SERIAL OUTPUT (SO): The SO pin is an output-only pin and is used to shift data out from the
device.
SERIAL CLOCK (SCK): The SCK pin is an input-only pin and is used to control the flow of data
to and from the DataFlash. Data is always clocked into the device on the rising edge of SCK and
clocked out of the device on the falling edge of SCK.
CHIP SELECT (CS): The DataFlash is selected when the CS pin is low. When the device is not
selected, data will not be accepted on the SI pin, and the SO pin will remain in a high-impedance
state. A high-to-low transition on the CS pin is required to start an operation, and a low-to-high
transition on the CS pin is required to end an operation.
8
AT45DB081B
2225J–DFLSH–2/08
相关PDF资料 |
PDF描述 |
|---|---|
| T95D277K004CZAS | CAP TANT 270UF 4V 10% 2917 |
| 395-072-527-204 | CARD EDGE 72POS DL .100X.200 BLK |
| ASPI-0412S-1R2N-T3 | INDUCTOR POWER MINI 1.2UH 0412 |
| T95D157M016EZSL | CAP TANT 150UF 16V 20% 2917 |
| 395-072-527-202 | CARD EDGE 72POS DL .100X.200 BLK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT45DB081D | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash |
| AT45DB081D_07 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash |
| AT45DB081D_08 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash |
| AT45DB081D_09 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.5-volt or 2.7-volt DataFlash |
| AT45DB081D_13 | 制造商:AD 制造商全称:Analog Devices 功能描述:8-megabit 2.5V or 2.7V DataFlash |
发布紧急采购，3分钟左右您将得到回复。