- 您现在的位置：买卖IC网 > PDF目录11205 > AT90USB1287-MUR (Atmel)MCU AVR 128K FLASH 16MHZ 64QFN PDF资料下载
参数资料
| 型号： | AT90USB1287-MUR |
| 厂商： | Atmel |
| 文件页数： | 59/106页 |
| 文件大小： | 0K |
| 描述： | MCU AVR 128K FLASH 16MHZ 64QFN |
| 产品培训模块： | MCU Product Line Introduction megaAVR Introduction |
| 标准包装： | 1,000 |
| 系列： | AVR® 90USB |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 16MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART，USB，USB OTG |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 48 |
| 程序存储器容量： | 128KB（128K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 64-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页当前第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页
56
7593L–AVR–09/12
AT90USB64/128
8.8.3
Brown-out detector
If the Brown-out Detector is not needed by the application, this module should be turned off. If
the Brown-out Detector is enabled by the BODLEVEL Fuses, it will be enabled in all sleep
modes, and hence, always consume power. In the deeper sleep modes, this will contribute sig-
nificantly to the total current consumption. Refer to “Brown-out detection” on page 60 for details
on how to configure the Brown-out Detector.
8.8.4
Internal voltage reference
The internal voltage reference will be enabled when needed by the Brown-out Detection, the
Analog Comparator or the ADC. If these modules are disabled as described in the sections
above, the internal voltage reference will be disabled and it will not be consuming power. When
turned on again, the user must allow the reference to start up before the output is used. If the
reference is kept on in sleep mode, the output can be used immediately. Refer to “Internal volt-
age reference” on page 62 for details on the start-up time.
8.8.5
Watchdog timer
If the Watchdog Timer is not needed in the application, the module should be turned off. If the
Watchdog Timer is enabled, it will be enabled in all sleep modes, and hence, always consume
power. In the deeper sleep modes, this will contribute significantly to the total current consump-
tion. Refer to “Interrupts” on page 68 for details on how to configure the Watchdog Timer.
8.8.6
Port pins
When entering a sleep mode, all port pins should be configured to use minimum power. The
most important is then to ensure that no pins drive resistive loads. In sleep modes where both
the I/O clock (clk
I/O) and the ADC clock (clkADC) are stopped, the input buffers of the device will
be disabled. This ensures that no power is consumed by the input logic when not needed. In
some cases, the input logic is needed for detecting wake-up conditions, and it will then be
enabled. Refer to the section “Digital input enable and sleep modes” on page 75 for details on
which pins are enabled. If the input buffer is enabled and the input signal is left floating or have
an analog signal level close to V
CC/2, the input buffer will use excessive power.
For analog input pins, the digital input buffer should be disabled at all times. An analog signal
level close to V
CC/2 on an input pin can cause significant current even in active mode. Digital
input buffers can be disabled by writing to the Digital Input Disable Registers (DIDR1 and
DIDR0). Refer to “DIDR1 – Digital Input Disable Register 1” on page 306 and “DIDR0 – Digital
Input Disable Register 0” on page 326 for details.
8.8.7
On-chip debug system
If the On-chip debug system is enabled by the OCDEN Fuse and the chip enters sleep mode,
the main clock source is enabled, and hence, always consumes power. In the deeper sleep
modes, this will contribute significantly to the total current consumption.
There are three alternative ways to disable the OCD system:
Disable the OCDEN Fuse
Disable the JTAGEN Fuse
Write one to the JTD bit in MCUCR
相关PDF资料 |
PDF描述 |
|---|---|
| AT90USB1287-AUR | MCU AVR 128K FLASH 16MHZ 64TQFP |
| VE-BTF-IX | CONVERTER MOD DC/DC 72V 75W |
| VI-B3X-IX-F2 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-BTF-IW | CONVERTER MOD DC/DC 72V 100W |
| VI-B3X-IW-F4 | CONVERTER MOD DC/DC 5.2V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT90USB128X | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:USB DFU Bootloader |
| AT90USB162 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 8/16K Bytes of ISP Flash and USB Controller |
| AT90USB162-16AU | 功能描述:8位微控制器 -MCU AVR USB 16K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT90USB162-16AUR | 功能描述:8位微控制器 -MCU 16K Flash RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT90USB162-16MU | 功能描述:8位微控制器 -MCU AVR USB 16K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。