- 您现在的位置：买卖IC网 > PDF目录11216 > AT90USB82-16MUR (Atmel)MCU AVR USB 8K FLASH 32-QFN PDF资料下载
参数资料
| 型号： | AT90USB82-16MUR |
| 厂商： | Atmel |
| 文件页数： | 13/38页 |
| 文件大小： | 0K |
| 描述： | MCU AVR USB 8K FLASH 32-QFN |
| 产品培训模块： | MCU Product Line Introduction megaAVR Introduction |
| 标准包装： | 5,000 |
| 系列： | AVR® 90USB |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 16MHz |
| 连通性： | EBI/EMI，PS/2，SPI，UART/USART，USB |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 22 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 512 x 8 |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 配用： | ATSTK600-ND - DEV KIT FOR AVR/AVR32 ATSTK526-ND - KIT STARTER FOR AT90USB82/162 ATAVRDRAGON-ND - KIT DRAGON FLASH MEM AVR ATSTK525-ND - KIT STARTER FOR AT90USB AT90USBKEY2-ND - KIT DEMO FOR AT90USB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
20
7707F–AVR–11/10
AT90USB82/162
5.3.4
The EEPROM Control Register – EECR
Bits 7..6 – Res: Reserved Bits
These bits are reserved bits in the AT90USB82/162 and will always read as zero.
Bits 5, 4 – EEPM1 and EEPM0: EEPROM Programming Mode Bits
The EEPROM Programming mode bit setting defines which programming action that will be trig-
gered when writing EEPE. It is possible to program data in one atomic operation (erase the old
value and program the new value) or to split the Erase and Write operations in two different
operations. The Programming times for the different modes are shown in Table 5-1. While EEPE
is set, any write to EEPMn will be ignored. During reset, the EEPMn bits will be reset to 0b00
unless the EEPROM is busy programming.
Bit 3 – EERIE: EEPROM Ready Interrupt Enable
Writing EERIE to one enables the EEPROM Ready Interrupt if the I bit in SREG is set. Writing
EERIE to zero disables the interrupt. The EEPROM Ready interrupt generates a constant inter-
rupt when EEPE is cleared.
Bit 2 – EEMPE: EEPROM Master Programming Enable
The EEMPE bit determines whether setting EEPE to one causes the EEPROM to be written.
When EEMPE is set, setting EEPE within four clock cycles will write data to the EEPROM at the
selected address If EEMPE is zero, setting EEPE will have no effect. When EEMPE has been
written to one by software, hardware clears the bit to zero after four clock cycles. See the
description of the EEPE bit for an EEPROM write procedure.
Bit 1 – EEPE: EEPROM Programming Enable
The EEPROM Write Enable Signal EEPE is the write strobe to the EEPROM. When address
and data are correctly set up, the EEPE bit must be written to one to write the value into the
EEPROM. The EEMPE bit must be written to one before a logical one is written to EEPE, other-
wise no EEPROM write takes place. The following procedure should be followed when writing
the EEPROM (the order of steps 3 and 4 is not essential):
1.
Wait until EEPE becomes zero.
2.
Wait until SELFPRGEN in SPMCSR becomes zero.
3.
Write new EEPROM address to EEAR (optional).
Bit
7
6
5432
10
–
EEPM1
EEPM0
EERIE
EEMPE
EEPE
EERE
EECR
Read/Write
R
R/W
Initial Value
0
X
0
X
0
Table 5-1.
EEPROM Mode Bits
EEPM1
EEPM0
Programming
Time
Operation
0
3.4 ms
Erase and Write in one operation (Atomic Operation)
0
1
1.8 ms
Erase Only
1
0
1.8 ms
Write Only
1
–
Reserved for future use
相关PDF资料 |
PDF描述 |
|---|---|
| ADG201HSKR-REEL | IC SWITCH QUAD SPST 16SOIC |
| ADG1406BRUZ-REEL7 | IC MULTIPLEXER 8X1 28TSSOP |
| ADG201HSJPZ | IC SWITCH QUAD SPST 20PLCC |
| ADG333ABR | IC SWITCH QUAD SPDT 20SOIC |
| ADG333ABRS | IC SWITCH QUAD SPDT 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT90USBKEY | 功能描述:开发板和工具包 - AVR Demo board f/AVR MCU & AT90USB RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| AT90USBKEY2 | 功能描述:开发板和工具包 - AVR AVR USB Eval Kit RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| AT-910 | 制造商:HRS 制造商全称:HRS 功能描述:Stripline Mounting Fixed Attenuators (DC to 8 GHz) |
| AT-910(40) | 功能描述:衰减器 -IC RoHS:否 制造商:Skyworks Solutions, Inc. 最大衰减:18 dB 容差: 阻抗: 功率额定值:30 dBm 安装风格:SMD/SMT 工作温度范围:- 40 C to + 85 C |
| AT-913(40) | 功能描述:衰减器 -IC RoHS:否 制造商:Skyworks Solutions, Inc. 最大衰减:18 dB 容差: 阻抗: 功率额定值:30 dBm 安装风格:SMD/SMT 工作温度范围:- 40 C to + 85 C |
发布紧急采购，3分钟左右您将得到回复。