- 您现在的位置：买卖IC网 > PDF目录11216 > AT90USB82-16MUR (Atmel)MCU AVR USB 8K FLASH 32-QFN PDF资料下载
参数资料
| 型号： | AT90USB82-16MUR |
| 厂商： | Atmel |
| 文件页数： | 14/38页 |
| 文件大小： | 0K |
| 描述： | MCU AVR USB 8K FLASH 32-QFN |
| 产品培训模块： | MCU Product Line Introduction megaAVR Introduction |
| 标准包装： | 5,000 |
| 系列： | AVR® 90USB |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 16MHz |
| 连通性： | EBI/EMI，PS/2，SPI，UART/USART，USB |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 22 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 512 x 8 |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 配用： | ATSTK600-ND - DEV KIT FOR AVR/AVR32 ATSTK526-ND - KIT STARTER FOR AT90USB82/162 ATAVRDRAGON-ND - KIT DRAGON FLASH MEM AVR ATSTK525-ND - KIT STARTER FOR AT90USB AT90USBKEY2-ND - KIT DEMO FOR AT90USB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
21
7707F–AVR–11/10
AT90USB82/162
4.
Write new EEPROM data to EEDR (optional).
5.
Write a logical one to the EEMPE bit while writing a zero to EEPE in EECR.
6.
Within four clock cycles after setting EEMPE, write a logical one to EEPE.
The EEPROM can not be programmed during a CPU write to the Flash memory. The software
must check that the Flash programming is completed before initiating a new EEPROM write.
Step 2 is only relevant if the software contains a Boot Loader allowing the CPU to program the
Flash. If the Flash is never being updated by the CPU, step 2 can be omitted. See “Memory Pro-
gramming” on page 243 for details about Boot programming.
Caution: An interrupt between step 5 and step 6 will make the write cycle fail, since the
EEPROM Master Write Enable will time-out. If an interrupt routine accessing the EEPROM is
interrupting another EEPROM access, the EEAR or EEDR Register will be modified, causing the
interrupted EEPROM access to fail. It is recommended to have the Global Interrupt Flag cleared
during all the steps to avoid these problems.
When the write access time has elapsed, the EEPE bit is cleared by hardware. The user soft-
ware can poll this bit and wait for a zero before writing the next byte. When EEPE has been set,
the CPU is halted for two cycles before the next instruction is executed.
Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable Signal EERE is the read strobe to the EEPROM. When the correct
address is set up in the EEAR Register, the EERE bit must be written to a logic one to trigger the
EEPROM read. The EEPROM read access takes one instruction, and the requested data is
available immediately. When the EEPROM is read, the CPU is halted for four cycles before the
next instruction is executed.
The user should poll the EEPE bit before starting the read operation. If a write operation is in
progress, it is neither possible to read the EEPROM, nor to change the EEAR Register.
The calibrated Oscillator is used to time the EEPROM accesses. Table 5-2 lists the typical pro-
gramming time for EEPROM access from the CPU.
The following code examples show one assembly and one C function for writing to the
EEPROM. The examples assume that interrupts are controlled (e.g. by disabling interrupts glob-
ally) so that no interrupts will occur during execution of these functions. The examples also
Table 5-2.
EEPROM Programming Time
Symbol
Number of Calibrated RC Oscillator Cycles
Typ Programming Time
EEPROM write
(from CPU)
26,368
3.3 ms
相关PDF资料 |
PDF描述 |
|---|---|
| ADG201HSKR-REEL | IC SWITCH QUAD SPST 16SOIC |
| ADG1406BRUZ-REEL7 | IC MULTIPLEXER 8X1 28TSSOP |
| ADG201HSJPZ | IC SWITCH QUAD SPST 20PLCC |
| ADG333ABR | IC SWITCH QUAD SPDT 20SOIC |
| ADG333ABRS | IC SWITCH QUAD SPDT 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT90USBKEY | 功能描述:开发板和工具包 - AVR Demo board f/AVR MCU & AT90USB RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| AT90USBKEY2 | 功能描述:开发板和工具包 - AVR AVR USB Eval Kit RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| AT-910 | 制造商:HRS 制造商全称:HRS 功能描述:Stripline Mounting Fixed Attenuators (DC to 8 GHz) |
| AT-910(40) | 功能描述:衰减器 -IC RoHS:否 制造商:Skyworks Solutions, Inc. 最大衰减:18 dB 容差: 阻抗: 功率额定值:30 dBm 安装风格:SMD/SMT 工作温度范围:- 40 C to + 85 C |
| AT-913(40) | 功能描述:衰减器 -IC RoHS:否 制造商:Skyworks Solutions, Inc. 最大衰减:18 dB 容差: 阻抗: 功率额定值:30 dBm 安装风格:SMD/SMT 工作温度范围:- 40 C to + 85 C |
发布紧急采购，3分钟左右您将得到回复。