参数资料
| 型号： | BD9011KV-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 15/30页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM 48-VQFP |
| 标准包装： | 1 |
| PWM 型： | 控制器 |
| 输出数： | 2 |
| 频率 - 最大： | 550kHz |
| 电源电压： | 3.9 V ~ 30 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 48-LQFP |
| 包装： | 标准包装 |
| 产品目录页面： | 1373 (CN2011-ZH PDF) |
| 其它名称： | BD9011KV-E2DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
10 ） In some application and process testing, Vcc and pin potential may be reversed, possibly causing internal circuit or element
damage. For example, when the external capacitor is charged, the electric charge can cause a Vcc short circuit to the GND.
In order to avoid these problems, limiting output pin capacitance to 100 μ F or less and inserting a Vcc series countercurrent
prevention diode or bypass diode between the various pins and the Vcc is recommended.
Bypass diode
Countercurrent prevention diode
Vcc
Pin
Fig-41
11 ） Thermal shutdown (TSD)
This IC is provided with a built-in thermal shutdown (TSD) circuit, which is designed to prevent thermal damage to or
destruction of the IC. Normal operation should be within the power dissipation parameter, but if the IC should run beyond
allowable Pd for a continued period, junction temperature (Tj) will rise, thus activating the TSD circuit, and turning all output
pins OFF. When Tj again falls below the TSD threshold, circuits are automatically restored to normal operation. Note that
the TSD circuit is only asserted beyond the absolute maximum rating. Therefore, under no circumstances should the TSD
be used in set design or for any purpose other than protecting the IC against overheating
12 ） The SW pin
When the SW pin is connected in an application, its coil counter-electromotive force may give rise to a single electric
potential. When setting up the application, make sure that the SW pin never exceeds the absolute maximum value.
Connecting a resistor of several Ω will reduce the electric potential. (See Fig. 43)
Vcc
BOOT
OUTH
SW
R
Vo
Fig-42
OUTL
DGND
13 ） Dropout operation
When input voltage falls below approximately output voltage / 0.9 (varying depending on operating frequency) the ON
interval on the OUTL side MOS is lost, making boost applications and wrap operation impossible. If a small differential
between input and output voltage is envisioned for a prospective application, connect the load such that the SW voltage
drops to the GND level. Managing this load requires discharging the SW line capacitance (SW pin capacitance: approx.
500pF; OUTL side MOS D-S capacitance; Schottky capacitance). Supported loads can be calculated using the equation
below.
Output voltage × SW line capacitance
ILOAD =
25n
Note that SW line capacitance is lower with smaller loads, and more stable operation is attained when low voltage bias
circuits are configured as in the example below (Fig. 44). However, the degree to which line capacitance is reduced or
operational stability is attained will vary depending on the board layout and components. Therefore, be certain to confirm
the effectiveness of these design factors in actual operation before entering mass production.
Vcc
VREG
Vcc
OUT
Vo
SW
OUT
Fig-43
15/29
相关PDF资料 |
PDF描述 |
|---|---|
| 1008-391K | COIL .39UH UNSHIELDED SMD |
| AVS107M50G24T-F | CAP ALUM 100UF 50V 20% SMD |
| ECM43DRYH | CONN EDGECARD 86POS DIP .156 SLD |
| AVS107M35G24T-F | CAP ALUM 100UF 35V 20% SMD |
| RBC17DREF-S734 | CONN EDGECARD 34POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD9012KV | 制造商:ROHM 制造商全称:Rohm 功能描述:Dual-output, high voltage, high-efficiency step-down switching controller |
| BD9012KV-E2 | 功能描述:开关变换器、稳压器与控制器 Step Down; 2 Outputs RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| BD9013KV-E2 | 功能描述:DC/DC 开关控制器 Step Down; 2 Outputs RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| BD9015KV-ME2 | 功能描述:Buck Regulator Positive Output Step-Down DC-DC Controller IC 48-VQFPC (7x7) 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:有效 输出类型:晶体管驱动器 功能:降压 输出配置:正 拓扑:降压 输出数:2 输出阶段:1 电压 - 电源（Vcc/Vdd）:3.9 V ~ 30 V 频率 - 开关:250kHz ~ 550kHz 占空比（最大）:- 同步整流器:是 时钟同步:是 串行接口:- 控制特性:使能，频率控制，电源良好，软启动 工作温度:-40°C ~ 105°C（TA） 封装/外壳:48-LQFP 供应商器件封装:48-VQFPC（7x7） 标准包装:1 |
| BD9016KV-ME2 | 制造商:ROHM Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。