参数资料
| 型号： | BD9011KV-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 9/30页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM 48-VQFP |
| 标准包装： | 1 |
| PWM 型： | 控制器 |
| 输出数： | 2 |
| 频率 - 最大： | 550kHz |
| 电源电压： | 3.9 V ~ 30 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 48-LQFP |
| 包装： | 标准包装 |
| 产品目录页面： | 1373 (CN2011-ZH PDF) |
| 其它名称： | BD9011KV-E2DKR |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
(4) Feedback resistor design
Please refer to the following equation in determining the proper feedback resistance. The recommended setting is in a range
between 10k Ω and 330k Ω . Resistance less than 10k Ω risks decreased power efficiency, while setting the resistance value
higher than 330k Ω will result in an internal error amp input bias current of 0.2uA increasing the offset voltage.
Vo
R8
Internal ref. 0.8V
Vo =
R8 +R9
R9
× 0.8 [V] ???（ 11 ）
FB
R9
Fig-20
(5) Setting switching frequency
The triangular wave switching frequency can be set by connecting a resistor to the RT 15(33) pin. The RT sets the frequency
by adjusting the charge/discharge current in relation to the internal capacitor. Refer to the figure below in determining proper
RT resistance, noting that the recommended resistance setting is between 50k Ω and 130k Ω . Settings outside this range
may render the switching function inoperable, and proper operation of the controller overall cannot be guaranteed when
unsupported resistance values are used.
550
500
450
400
350
300
250
50
60
70
80
90
100
110
120
130
RT [ kΩ]
Fig-21 RT vs. switching frequency
(6) Setting the soft start delay
The soft start function is necessary to prevent an inrush of coil current and output voltage overshoot at startup. The figure
below shows the relation between soft start delay time and capacitance, which can be calculated using equation (12) at right.
10
1
TSS =
0.8V(typ.) × CSS
[sec] ??? (12)
ISS(10 μ A Typ.)
0.1
0.01
0.001
0.01
0.1
SS CAPACITANCE[uF]
Fig-22 SS capacitance vs. delay time
Recommended capacitance values are between 0.01uF and 0.1uF. Capacitance lower than 0.01uF may generate output
overshoots. Please use high accuracy components (such as X5R) when implementing sequential startups involving other
power sources. Be sure to test the actual devices and applications to be used, since the soft start time varies, depending on
input voltage, output voltage and capacitance, coils and other characteristics.
9/29
相关PDF资料 |
PDF描述 |
|---|---|
| 1008-391K | COIL .39UH UNSHIELDED SMD |
| AVS107M50G24T-F | CAP ALUM 100UF 50V 20% SMD |
| ECM43DRYH | CONN EDGECARD 86POS DIP .156 SLD |
| AVS107M35G24T-F | CAP ALUM 100UF 35V 20% SMD |
| RBC17DREF-S734 | CONN EDGECARD 34POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD9012KV | 制造商:ROHM 制造商全称:Rohm 功能描述:Dual-output, high voltage, high-efficiency step-down switching controller |
| BD9012KV-E2 | 功能描述:开关变换器、稳压器与控制器 Step Down; 2 Outputs RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| BD9013KV-E2 | 功能描述:DC/DC 开关控制器 Step Down; 2 Outputs RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| BD9015KV-ME2 | 功能描述:Buck Regulator Positive Output Step-Down DC-DC Controller IC 48-VQFPC (7x7) 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:有效 输出类型:晶体管驱动器 功能:降压 输出配置:正 拓扑:降压 输出数:2 输出阶段:1 电压 - 电源（Vcc/Vdd）:3.9 V ~ 30 V 频率 - 开关:250kHz ~ 550kHz 占空比（最大）:- 同步整流器:是 时钟同步:是 串行接口:- 控制特性:使能，频率控制，电源良好，软启动 工作温度:-40°C ~ 105°C（TA） 封装/外壳:48-LQFP 供应商器件封装:48-VQFPC（7x7） 标准包装:1 |
| BD9016KV-ME2 | 制造商:ROHM Semiconductor 功能描述: |
发布紧急采购，3分钟左右您将得到回复。