参数资料
| 型号： | BD9328EFJ-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 8/18页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 2A 8HTSOP |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.9 V ~ 12.6 V |
| 输入电压： | 4.2 V ~ 18 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 380kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-HTSOP-J |
| 其它名称： | BD9328EFJ-E2DKR |
BD9328EFJ
Technical Note
● Selecting Application Components
(1) Output LC filter constant selection (Buck Converter)
The Output LC filter is required to supply constant current to the output load. A larger value inductance at this filter
results in less inductor ripple current( ? I L ) and less output ripple voltage. However, the larger value inductors tend to
have less fast load transient-response, a larger physical size, a lower saturation current and higher series resistance. A
smaller value inductance has almost opposite characteristics above. So Choosing the Inductor ripple current( ? I L )
between 20 to 40% of the averaged inductor current (equivalent to the output load current) is a good compromise.
I L
I OUTMAX + ? I L /2
should not reach
the rated value level
I LR
V IN
V OUT
Inductor averaged current
t
Fig.18
Setting ? I L = 30% x Averaged Inductor current (2A) = 0.6 [A]
L
C OUT
Fig.19
L=
V OUT ? (V IN - V OUT ) x
1
V IN x F OSC x ? I L
= 10μ [H]
Where V IN = 12V, V OUT = 3.3V, F OSC = 380 kHz,
; F OSC is a switching frequency
Also the inductor should have the higher saturation current than I OUTMAX + ? I L / 2.
The output capacitor C OUT affects the output ripple-voltage. Choose the large capacitor to achieve the small
ripple-voltage enough to meet the application requirement.
Output ripple voltage ? V RPL is calculated by the following equation.
? V RPL =
? I L ? ( R ESR +
1
8x C OUT x F OSC
) [V]
Where R ESR is a parasitic series resistance in output capacitor.
Setting C OUT = 20μF, R ESR = 10m Ω
? V RPL = 0.6 x (10m + 1 / (8 x 20μ x 380k)) = 15.8mV
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
8/15
2011.02 - Rev.A
相关PDF资料 |
PDF描述 |
|---|---|
| BD9329AEFJ-E2 | IC REG BUCK SYNC ADJ 3A 8HTSOP |
| BD9533EKN-E2 | IC REG SW VAR SOFT START 20-HQFN |
| BD95513MUV-E2 | IC REG BUCK ADJ 3A 32VQFN |
| BD9701T-V5 | IC REG BUCK ADJ 1.5A TO220FP |
| BD9739KN-E2 | IC REG SW BUILT IN FET 64UQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD93291EFJ-E2 | 功能描述:Buck Switching Regulator IC Positive Adjustable (Fixed) 0.8V (5V) 2 Output 1.7A, 500mA 8-SOIC (0.154", 3.90mm Width) Exposed Pad 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:可调（固定） 输出数:2 电压 - 输入（最小值）:8V 电压 - 输入（最大值）:26V 电压 - 输出（最小值/固定）:0.8V（5V） 电压 - 输出（最大值）:4V 电流 - 输出:1.7A，500mA 频率 - 开关:300kHz ~ 600kHz，1.5MHz ~ 2.5MHz 同步整流器:是 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽）裸焊盘 供应商器件封装:8-HTSOP-J 标准包装:1 |
| BD9329AEFJ | 制造商:ROHM 制造商全称:Rohm 功能描述:Simple Step-down Switching Regulator with Built-in Power MOSFET |
| BD9329AEFJ_EVK | 制造商:ROHM Semiconductor 功能描述:BOARD EVAL BUCK REG BD9329A |
| BD9329AEFJ-E2 | 功能描述:IC REG BUCK SYNC ADJ 3A 8HTSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:升压（升压） 输出类型:两者兼有 输出数:1 输出电压:5V，2 V ~ 16.5 V 输入电压:2 V ~ 16.5 V PWM 型:- 频率 - 开关:45kHz 电流 - 输出:50mA 同步整流器:无 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 供应商设备封装:8-PDIP |
| BD9329EFJ-E2 | 制造商:ROHM Semiconductor 功能描述:CONV DC-DC SINGLE STEP DOWN 4.2V TO 18V 8-PIN HTSOP-J T/R - Tape and Reel 制造商:ROHM Semiconductor 功能描述:IC REG BUCK SYNC ADJ 3A 8-HTSOP |
发布紧急采购，3分钟左右您将得到回复。