参数资料
| 型号： | BD9853AFV-E2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 14/17页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 16-SSOP |
| 标准包装： | 1 |
| PWM 型： | 控制器 |
| 输出数： | 2 |
| 频率 - 最大： | 2MHz |
| 电源电压： | 4.5 V ~ 16 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 包装： | 标准包装 |
| 产品目录页面： | 1373 (CN2011-ZH PDF) |
| 其它名称： | BD9853AFV-E2DKR |
BD9853AFV
Technical Note
● Notes for use
1) Absolute maximum ratings
Use of the IC in excess of absolute maximum ratings such as the applied voltage or operating temperature range may
result in IC deterioration or damage. Assumptions should not be made regarding the state of the IC (short mode or open
mode) when such damage is suffered. A physical safety measure such as a fuse should be implemented when use of the
IC in a special mode where the absolute maximum ratings may be exceeded is anticipated.
2) GND potential
Ensure a minimum GND pin potential in all operating conditions. In addition, ensure that no pins other than the GND pin
carry a voltage lower than or equal to the GND pin, including during actual transient phenomena.
3) Thermal design
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
4) Inter-pin shorts and mounting errors
Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting may result in
damage to the IC. Shorts between output pins or between output pins and the power supply and GND pin caused by the
presence of a foreign object may result in damage to the IC.
5) Operation in a strong electromagnetic field
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to
malfunction.
6) Thermal shutdown circuit (TSD circuit)
This IC incorporates a built-in thermal shutdown circuit (TSD circuit). The TSD circuit is designed only to shut the IC off to
prevent runaway thermal operation. Do not continue to use the IC after operating this circuit or use the IC in an
environment where the operation of the thermal shutdown circuit is assumed.
7) Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.
Always discharge capacitors after each process or step. Ground the IC during assembly steps as an antistatic measure,
and use similar caution when transporting or storing the IC. Always turn the IC's power supply off before connecting it to or
removing it from a jig or fixture during the inspection process.
8) Common impedance
Power supply and ground wiring should reflect consideration of the need to lower common impedance and minimize ripple
as much as possible
(by making wiring as short and thick as possible or rejecting ripple by incorporating inductance and capacitance).
9) Applications with modes that reverse VCC and pin potentials may cause damage to internal IC circuits.
For example, such damage might occur when VCC is shorted with the GND pin while an external capacitor is charged.
It is recommended to insert a diode for preventing back current flow in series with VCC or bypass diodes between VCC
and each pin.
Bypass diode
Back current prevention diode
VCC
Output Pin
10) Pin short and mistake fitting
Do not short-circuit between OUT pin and VCC pin, OUT pin and GND pin, or VCC pin and GND pin.
When soldering the IC on circuit board,
please be unusually cautious about the orientation and the position of the IC.
11) Timing resistor and capacitor
Timing resistor connected between RT and GND, has to be placed near RT terminal. And pattern has to be short enough.
www.rohm.com
? 2009 ROHM Co., Ltd. All rights reserved.
14/16
2009.05 - Rev.A
相关PDF资料 |
PDF描述 |
|---|---|
| BD9862MUV-E2 | IC PMIC PS TFT-LCD 24VQFN |
| BH25FB1WG-TR | IC REG LDO 2.5V .15A 5SSOP |
| BH30NB1WHFV-TR | IC REG LDO 3V .15A 5HVS0F |
| BH31PB1WHFV-TR | IC REG LDO 3.1V .15A HVSOF5 |
| BH31RB1WGUT-E2 | IC REG LDO 3.1V .15A 4-VCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BD9853FV | 制造商:ROHM 制造商全称:Rohm 功能描述:2 Channel Switching Regulator Controller |
| BD9855MWV | 制造商:ROHM 制造商全称:Rohm 功能描述:Silicon Monolithic Integrated Circuit |
| BD9859EFJ | 制造商:ROHM 制造商全称:Rohm 功能描述:Simple Step-down Switching Regulators with Built-in Power MOSFET |
| BD9859EFJ-E2 | 制造商:ROHM Semiconductor 功能描述: |
| BD9860MUV-E2 | 制造商:ROHM Semiconductor 功能描述:3CH SWITCH. REG. CONTROLLER - Tape and Reel 制造商:ROHM Semiconductor 功能描述:IC REG CTLR SW 3CH VQFNV4040 |
发布紧急采购，3分钟左右您将得到回复。