- 您现在的位置：买卖IC网 > PDF目录16573 > BUF20820EVM (Texas Instruments)EVAL MOUDLE FOR BUF20820 PDF资料下载
参数资料
| 型号： | BUF20820EVM |
| 厂商： | Texas Instruments |
| 文件页数： | 2/29页 |
| 文件大小： | 0K |
| 描述： | EVAL MOUDLE FOR BUF20820 |
| 标准包装： | 1 |
| 系列： | * |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
BUF20820
SBOS330E DECEMBER 2005 REVISED OCTOBER 2008
www.ti.com
10
addressed register, the master continues to send data for
the next register. The BUF20820 automatically and
sequentially steps through subsequent registers as
additional data is sent. The process continues until all
desired registers have been updated or a STOP condition
is sent.
To write to multiple DAC registers:
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The BUF20820 will acknowledge this byte.
3.
Send either the DAC_1 address byte to start at the first
DAC, or send the address byte for whichever DAC will
be the first in the sequence of DACs to be updated.
The BUF20820 will begin with this DAC and step
through subsequent DACs in sequential order.
4.
Send the bytes of data; begin by sending the most
significant byte (bits D15D8, of which only bits D9
and D8 have meaning, and bits D15D14 must not be
01), followed by the least significant byte (bits D7D0).
The first two bytes are for the DAC addressed in step
3 above. Its register is automatically updated after
receiving the second byte. The next two bytes are for
the following DAC. That DAC register is updated after
receiving the fourth byte. This process continues until
the registers of all following DACs have been updated.
The last address, 10100, is the address of the write
disable bit and cannot be accessed using this method.
It must be written using the write to a single DAC
register procedure.
5.
Send a STOP condition on the bus.
The BUF20820 will acknowledge each byte. To terminate
communication, send a STOP or START condition on the
bus. Only DAC registers that have received both bytes of
data will be updated.
Reading:
Reading a DAC register will return the data stored in the
DAC. This data can differ from the data stored in the DAC
register. See the Output Latch section.
To read the DAC value:
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The BUF20820 will acknowledge this byte.
3.
Send the DAC address byte. Bits D7D5 must be set
to 0; Bits D4D0 are the DAC address. Only DAC
addresses 00000 to 10100 are valid and will be
acknowledged. For address 10100, only D0 has
meaning. This bit is the write disable bit.
4.
Send a START or STOP/START condition on the bus.
5.
Send
correct
device
address
and
read/write
bit = HIGH. The BUF20820 will acknowledge this
byte.
6.
Receive two bytes of data. They are for the specified
DAC. The first received byte is the most significant
byte (bits D15D8, only bits D9 and D8 have
meaning); the next byte is the least significant byte
(bits D7D0).
7.
Acknowledge after receiving the first byte.
8.
Do not acknowledge the second byte to end the read
transaction.
Communication may be terminated by sending a
premature STOP or START condition on the bus, or by not
sending the acknowledge.
To Read Multiple DACs:
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The BUF20820 will acknowledge this byte.
3.
Send either the DAC_1 address byte to start at the first
DAC, or send the address byte for whichever DAC will
be the first in the sequence of DACs to be read. The
BUF20820 will begin with this DAC and step through
subsequent DACs in sequential order.
4.
Send a START or STOP/START condition on the bus.
5.
Send
correct
device
address
and
read/write
bit = HIGH. The BUF20820 will acknowledge this
byte.
6.
Receive two bytes of data. They are for the specified
DAC. The first received byte is the most significant
byte (bits D15D8, only bits D9 and D8 have
meaning), the next byte is the least significant byte
(bits D7D0).
7.
Acknowledge after receiving each byte of data except
for the last byte. The acknowledge bit of the last byte
should be HIGH to end the read operation.
8.
When all desired DACs have been read, send a STOP
or START condition on the bus.
Communication may be terminated by sending a
premature STOP or START condition on the bus, or by not
sending the acknowledge.
相关PDF资料 |
PDF描述 |
|---|---|
| M1BXA-2436R | IDC CABLE - MSR24A/MC24M/X |
| RBM06DCMT | CONN EDGECARD 12POS .156 WW |
| GBC10DRSN-S273 | CONN EDGECARD 20POS DIP .100 SLD |
| GEM25DTMT-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| SRP7030-R47M | INDUCTOR SHIELDED PWR 0.47UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BUF22821 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Programmable Gamma-Voltage Generator and VCOM Calibrator with Integrated Two-Bank Memory |
| BUF22821AIDCPR | 功能描述:LCD Gamma缓冲器 Prgrmbl Gam-Vltg Gen & Vcom Calibrator RoHS:否 制造商:Maxim Integrated 输入补偿电压: 转换速度: 电源电压-最大:20 V 电源电压-最小:9 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-38 封装:Tube |
| BUF22821EVM | 功能描述:放大器 IC 开发工具 BUF22821EVM Eval Mod RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| BUF22821EVM-USB | 功能描述:放大器 IC 开发工具 BUF22821 Eval board Mod RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| BUF298AF | 制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | BJT POWER MODULE | INDEPENDENT | 450V V(BR)CEO | 50A I(C) |
发布紧急采购，3分钟左右您将得到回复。