参数资料
| 型号： | CDB5467U |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 32/46页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR CS5467 ADC |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电度表/功率表 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | CS5467 |
| 主要属性： | 电能表 |
| 次要属性： | 图形用户接口，SPI? 和 USB 接口 |
| 已供物品： | 板，线缆，软件 |
| 产品目录页面： | 754 (CN2011-ZH PDF) |
| 相关产品： | CS5467-ISZR-ND - IC ENERGY METERING 1PHASE 28SSOP 598-1197-5-ND - IC ENERGY METERING 1PHASE 28SSOP |
| 其它名称： | 598-1555 CDB-5467U |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
CS5467
8.2.12 Internal Status (Status) and Interrupt Mask (Mask)
Address: 15 ( Status ); 26 ( Mask )
23
DRDY
15
E2OR
7
TUP
22
I2OR
14
I1ROR
6
V2OD
21
V2OR
13
V1ROR
5
I2OD
20
CRDY
12
E1OR
4
V1OD
19
I2ROR
11
I1FAULT
3
I1OD
18
V2ROR
10
V1SAG
2
LSD
17
I1OR
9
I2FAULT
1
FUP
16
V1OR
8
V2SAG
0
IC
Default =
1 ( Status ), 0 ( Mask )
The Status register indicates a variety of conditions within the chip. Writing a '1' to a Status register bit will
clear that bit if the condition that set it has been removed. Writing a '0' to any bit has no effect.
The Mask register is used to control the activation of the INT pin. Writing a '1' to a Mask register bit will allow
the corresponding Status register bit to activate the INT pin when set.
DRDY
I1OR (I2OR)
V1OR (V2OR)
CRDY
I1ROR (I2ROR)
Data Ready. During conversion, this bit indicates that low-rate results have been updated.
It indicates completion of other commands and the reset sequence.
Current Out of Range. Set when the measured current would cause the I1 ( I2 ) register to
overflow.
Voltage Out of Range. Set when the measured voltage would cause the V1 ( V2 ) register
to overflow.
Conversion Ready. Indicates that sample rate (output word rate) results have been updat-
ed.
RMS Current Out of Range. Set when RMS current would cause the I1 RMS ( I2 RMS ) regis-
ter to overflow.
V1ROR (V2ROR) RMS Voltage Out of Range. Set when RMS voltage would cause the V1 RMS ( V2 RMS ) reg-
ister to overflow.
E1OR (E2OR)
Energy Out of Range. Set when average power would cause P1 AVG ( P2 AVG ) to overflow.
I1FAULT (I2FAULT)Indicates when a current fault condition has occurred.
32
V1SAG (V2SAG)
TUP
V1OD (V2OD)
I1OD (I2OD)
LSD
FUP
IC
Indicates when a voltage sag condition has occurred.
Indicates when the Temperature register ( T ) has been updated.
Modulator oscillation has been detected in the voltage1 (voltage2) A/D.
Modulator oscillation has been detected in the current1 (current2) A/D.
Low Supply Detect. Set when the voltage on the PFMON pin falls below the specified low
level. The LSD bit cannot be reset until the voltage rises above the specified high level.
Frequency Updated. Indicates the Epsilon register has been updated.
Invalid Command. Normally logic 1. Set to 0 when an invalid command is received. It may
also indicate loss of serial command synchronization and the part may need to be re-ini-
tialized.
DS714F3
相关PDF资料 |
PDF描述 |
|---|---|
| CDB5560-2 | DEV BOARD FOR CS5560 W/SE INPUT |
| CDB5571-2 | DEV BOARD FOR CS5571 W/SE INPUT |
| CDB8422 | BOARD EVAL FOR CS8422 RCVR |
| CDB8952T | BOARD EVAL FOR CS8952 |
| CDCE906-706PERFEVM | EVAL MOD PERFORMANCE CDCE906/706 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB5471 | 制造商:Cirrus Logic 功能描述:Tools Development kit Kit Con |
| CDB5480U-Z | 功能描述:电源管理IC开发工具 CS5480 Eval Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| CDB5484U-Z | 功能描述:电源管理IC开发工具 CS5484 Eval Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| CDB5490U-Z | 功能描述:电源管理IC开发工具 CS5490 Eval Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| CDB5501 | 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5501 - Bulk |
发布紧急采购，3分钟左右您将得到回复。