- 您现在的位置：买卖IC网 > PDF目录16440 > CDB8420 (Cirrus Logic Inc)EVALUATION BOARD FOR CS8420 PDF资料下载
参数资料
| 型号： | CDB8420 |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 24/94页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR CS8420 |
| 标准包装： | 1 |
| 主要目的： | 音频，采样率转换器 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | CS8420 |
| 主要属性： | 带数字音频发射器和接收器的采样率转换器 |
| 次要属性： | 44.1、48、96 kHz 输出采样率，AES/EBU，S/PDIF，EIAJ-340，GUI |
| 已供物品： | 板 |
| 相关产品： | 598-1125-5-ND - IC SAMPLE RATE CONVERTER 28SOIC |
| 其它名称： | 598-1782 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
30
DS245F4
CS8420
9.
CONTROL PORT DESCRIPTION AND TIMING
The control port is used to access the registers, allowing the CS8420 to be configured for the desired operational
modes and formats. In addition, Channel Status and User data may be read and written via the control port. The
operation of the control port may be completely asynchronous with respect to the audio sample rates. However, to
avoid potential interference problems, the control port pins should remain static if no operation is required.
The control port has two modes: SPI and IC, with the CS8420 acting as a slave device. SPI mode is selected if
there is a high-to-low transition on the AD0/CS pin after the RST pin has been brought high. IC mode is selected
by connecting the AD0/CS pin to VD+ or DGND, thereby permanently selecting the desired AD0 bit address state.
9.1
SPI Mode
In SPI mode, CS is the CS8420 chip select signal. CCLK is the control port bit clock (input into the CS8420
from the microcontroller), CDIN is the input data line from the microcontroller, CDOUT is the output data line
to the microcontroller. Data is clocked in on the rising edge of CCLK and out on the falling edge.
Figure 22 shows the operation of the control port in SPI mode. To write to a register, bring CS low. The first
7 bits on CDIN form the chip address and must be 0010000b. The eighth bit is a read/write indicator (R/W),
which should be low to write. The next 8 bits form the Memory Address Pointer (MAP), which is set to the
address of the register that is to be updated. The next 8 bits are the data which will be placed into the register
designated by the MAP. During writes, the CDOUT output stays in the Hi-Z state. It may be externally pulled
high or low with a 47 k
Ω resistor, if desired.
There is a MAP auto-increment capability, enabled by the INCR bit in the MAP register. If INCR is a zero,
then the MAP will stay constant for successive read or writes. If INCR is set to a 1, then the MAP will auto-
increment after each byte is read or written, allowing block reads or writes of successive registers.
To read a register, the MAP has to be set to the correct address by executing a partial write cycle which
finishes (CS high) immediately after the MAP byte. The MAP auto-increment bit (INCR) may be set or not,
as desired. To begin a read, bring CS low, send out the chip address and set the read/write bit (R/W) high.
The next falling edge of CCLK will clock out the MSB of the addressed register (CDOUT will leave the high-
impedance state). If the MAP auto-increment bit is set to 1, the data for successive registers will appear
consecutively.
MA P
MSB
LSB
DATA
by te 1
by te n
R/W
AD D R ESS
CH IP
ADDRESS
CH IP
CD IN
CC L K
CS
CD O U T
MSB
LSB MSB
LSB
0010000
MAP = Memory Address Pointer, 8 bits, MSB first
High Impedance
Figure 22. Control Port Timing in SPI Mode
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J11-EX | CONVERTER MOD DC/DC 12V 75W |
| GEM28DTAT | CONN EDGECARD 56POS R/A .156 SLD |
| 6278895-7 | C/A 62.5/125 RIS SC MTRJ 7M1 |
| A3BBB-2436G | IDC CABLE- ASR24B/AE24G/ASR24B |
| GSM12DTAN | CONN EDGECARD 24POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB8421 | 功能描述:音频 IC 开发工具 2-Ch 32-Bit 192kHz sample rate converte RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| CDB8422 | 功能描述:界面开发工具 Eval Bd 192kHz SRC S/PDIF Receiver RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| CDB8427 | 功能描述:音频 IC 开发工具 Eval Bd 96kHz Dig. Audio Transcvr RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| CDB8952 | 制造商:Cirrus Logic 功能描述:NOT RECOMMENDED FOR NEW DESIGNS - USE CDB8952T - Bulk 制造商:Cirrus Logic 功能描述:Tools Development kit Kit Con |
| CDB8952T | 功能描述:以太网开发工具 Eval Bd 100BASE-TX/ 10BASE-T Transceiver RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。