参数资料
型号: CPC1590P
厂商: IXYS Integrated Circuits Division
文件页数: 7/10页
文件大小: 0K
描述: MOSFET GATE DVR ISO 8-FLATPACK
标准包装: 50
系列: *
I NTEGRATED C IRCUITS D IVISION
4. Device Configuration
CPC1590
V I N
CPC1590
8
CAP
1
4
N C
N C
7 A
LOAD
+V LOAD
R LED
2
5
C ST
G
3
6 B
-V LOAD
4.1 LED resistor
The input resistor is required to limit LED current to a
value set by Recommended Operating Conditions in
“Recommended Operating Conditions” on page 3 . In some
cases, higher LED operating current would improve
driver speed; however, this higher current could also
reduce LED lifespan, which would cause reliability
issues.
The general equation used to calculate the resistor
value is:
When the LED resistor value is selected by the above
formula, the R LED power dissipation, P D , can be
obtained from the following equation:
P D = I F2 ? R LED
With power dissipation calculated, it is now possible to
select an appropriate resistor size that can be used in
the particular application circuit. It is recommended
that a resistor with at least twice the calculated power
rating should be selected.
R LED =
V IN - (V F + V OL )
I F
4.2 Storage Capacitor
? I F = Input Control Current
? V OL = Low-level output of the driving logic gate or the
collector-emitter voltage of the driving logic transis-
tor. (This parameter is provided in the manufacturer’s
data sheet.)
? V IN = Input Power Source
? V F = Forward Voltage Drop of LED
? R LED = Input Resistor
When calculating the resistor value, the designer
should take into consideration power-supply
variations, which can range about ±10%, temperature
variations from -40°C to +85°C, LED forward voltage
drop over the temperature range, and the resistor’s
tolerance and temperature stability rating.
The storage capacitor (C ST ) enables the gate driver to
turn on a power MOSFET faster by delivering a
reservoir of charge to the gate. Selection of the
storage capacitor is given by the following equation:
C ST > Q G / 0.5V
This equation shows that the storage capacitor needs
to deliver enough charge to the gate while only
dropping 0.5V. The CPC1590 can deliver 32nC of
charge at rated operating speed, and will operate with
much larger loads, >4nF, with slower turn-on and
turn-off times.
The CPC1590 has an internal J-FET, which is used to
regulate the voltage applied to the storage capacitor.
The voltage applied to the storage capacitor will be
R01
www.ixysic.com
7
相关PDF资料
PDF描述
CPC5002G ISOLAT DGTL 3.75KVRMS 2CH 8-DIP
CPCI-D-3U-300C PWR SUPLY DC/DC CPCI 300W 3UX8HP
CPD250-4530G PWR SUP 250W 3.3/5/12/-12V QUAD
CS4161YN8 IC DRIVER H-BRDG DUAL 85MA 8DIP
CS5461A-ISZ IC ENERGY METERING 1PHASE 24SSOP
相关代理商/技术参数
参数描述
CPC1590PTR 功能描述:逻辑输出光电耦合器 Optically Isolated Gate Driver, Tape/Reel RoHS:否 制造商:Fairchild Semiconductor 绝缘电压:4243 Vrms 输出类型:Push-Pull 最大传播延迟时间:500 ns 最大正向二极管电压: 最大反向二极管电压: 最大正向二极管电流: 最大连续输出电流:2.5 A 最大功率耗散:100 mW 最大工作温度:+ 100 C 最小工作温度:- 40 C 封装 / 箱体:SO-16 封装:Tube
CPC1593 制造商:IXYS 制造商全称:IXYS Corporation 功能描述:Single-Pole, Normally Open OptoMOS?? Relay Integrated Current Limit with Voltage and Thermal Protection
CPC1593G 功能描述:固态继电器-PCB安装 1-Form-A 600V 6-Pin DIP RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT
CPC1593GS 功能描述:固态继电器-PCB安装 1-Form-A 600V 6-Pin SM RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT
CPC1593GSTR 功能描述:固态继电器-PCB安装 1-Form-A 600V 6-Pin SM T/R RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT