参数资料
| 型号： | CS1601-FSZ |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC PFC CONTROLLER BALLAST 8SOIC |
| 产品变化通告： | CS1501, 1601 Datasheet Update Change 11/Jan/2012 |
| 设计资源： | CS150x/160x PCB Layout Guidelines Driving Mosfets with CS1501/1601 CS1501/1601 Driving ZCD Pin from Mosfet Drain |
| 特色产品： | CS1501/CS1601 Power Factor Correction IC Controllers |
| 标准包装： | 100 |
| 类型： | PFC/镇流器控制器 |
| 频率： | 70kHz |
| 电流 - 电源： | 1.5mA |
| 电流 - 输出： | 1A |
| 电源电压： | 7.9 V ~ 17 V |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 散装 |
| 其它名称： | 598-1915 |
CS1601
table below depicts approximate values for R3 and R4 for a
range of boost-to-auxiliary inductor turns ratio, N.
The overpower protection may activate prior to brownout
protection, depending on the load.
N
~R3
~R4
T Brownout
56 ms
9
10
46k ?
42k ?
1.75k ?
1.75k ?
Brownout
Thresholds
Upper
56 ms
11
12
13
37.5k ?
35.5k ?
32k ?
1.75k ?
1.75k ?
1.75k ?
Lower
Start
Timer
14
15
29.5k ?
27.5k ?
1.75k ?
1.75k ?
Enter Standby
Start Timer
Exit Standby
Table 1. Aux Inductor Turns Ratio vs. R3 and R4
Resistors R3 and R4 were calculated using V link = 460V and
C p = 10pF.
Equation 6 is used to calculate the cut-off frequency defined
Figure 21. Brownout Sequence
The maximum response time of the brownout protection
feature occurs at light-load conditions. It is calculated by
Equation 7.
T Brownout = 8 ms + ------------ ? 128 V – V BP ? th ? ? + 56 ms [Eq.7]
by the RC circuit at the ZCD pin.
f c = 1 ? ? 2 ? ? R3 ?? R4 ? C p ?
where:
[Eq.6]
---
= 8 + 8 ? 128 – 94.8 ? + 56 = 117ms
5
8 ms
5V
f c
C p
The cut-off frequency, f c , needs to be 10x the ringing
frequency.
Capacitance at the ZCD pin
where:
V BP(th) Brownout threshold voltage, V BP(th) = I BP(lower) xR IAC
5.9 Overvoltage Protection
5.8 Brownout Protection
The CS1601 brownout detection circuit monitors the peak of
the V rect input voltage and disables the PWM switching when
it drops below a predetermined threshold. Hysteresis and
minimum detection time are provided to avoid brownout
detection during short input transients. When brownout is
The overvoltage protection (OVP) will trigger immediately and
stop the gate drive when the current into the IFB pin (I OVP )
exceeds 105% of the reference current (I ref ) value. The IC
resumes gate drive switching when the measured current at IFB
drops below I OVP – I OVP(Hy) . Equation 8 is used to calculate the
OVP threshold (V OVP ).
detected, the CS1601 enters standby mode. On recovery from
brownout, it re-enters normal operating mode.
V OVP = R IFB ? I OVP + V DD
[Eq.8]
Current I AC is proportional to the AC input voltage V rect , where
page 11). The digitized current applied to the IAC pin is
monitored by the brownout protection algorithm. When V rect
drops below the brownout detection threshold, the CS1601
triggers a timer. The IC asserts the brownout protection and
stops the gate-drive switching only if the timer exceeds 56ms.
This is the equivalent of 7 rectified line cycles at 60Hz.
During the brownout state, the device continues monitoring
the input line voltage. The device exits the brownout state
when I AC exceeds the brownout upper threshold for at least
56ms. Typical values for the lower (I BP(lower) ) and upper
(I BP(upper) ) brownout thresholds are 31.6 ? A and 39.6 ? A,
respectively.
12
5.10 Overcurrent Protection
To limit boost inductor current through the FET and to prevent
boost inductor saturation conditions, the CS1601 incorporates
a cycle-by-cycle peak inductor current limit circuit using an
external shunt resistor to ‘sense’ the FET source current
accurately. The overcurrent protection (OCP) circuit is
designed to monitor the current when the active switch is
turned on. The OCP circuit is enabled after the leading-edge
blanking time (t LEB ). The shunt voltage is compared to a
reference voltage, V c s ( t h ) , to determine whether an
overcurrent condition exists. The OCP circuit triggers
immediately, allowing the OCP algorithm to turn off the gate
driver.
The overcurrent protection circuit is also designed to monitor
for a catastrophic overcurrent occurrence by sensing sudden
and abnormal operating currents. A second OCP threshold,
V cs(clamp) , determines whether a severe overcurrent condition
exists. This immediately turns off the gate drive, and the
system enters a restart mode. The CS1601 inhibits all
switching operations for approximately 1.6 ms and then
attempts to restart normal operation.
DS931F3
相关PDF资料 |
PDF描述 |
|---|---|
| CS2001YDWFR20 | IC REG BST FLYBK ADJ 1.2A 20SOIC |
| CS2841BEDR14G | IC REG CTRLR BST FLYBK CM 14SOIC |
| CS5101EN14G | IC REG BUCK 5V 1.5A 14DIP |
| CS51033GDR8G | IC REG CTRLR BUCK PWM 8-SOIC |
| CS51414GD8 | IC REG BUCK 1.5A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS1601-FSZR | 制造商:Cirrus Logic 功能描述:IC PFC CONTROLLER DCM OCP (FOR LIGHTING) - Tape and Reel 制造商:Cirrus Logic 功能描述:IC PFC CTRLR BALLAST 8SOIC 制造商:Cirrus Logic 功能描述:PFC Controller |
| CS1601H | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Digital PFC Controller for Electronic Ballasts |
| CS1601H-FSZ | 制造商:Cirrus Logic 功能描述:IC PFC CONTROLLER DCM OCP (100KHZ) - Bulk 制造商:Cirrus Logic 功能描述:IC PFC CTRLR BALLAST 8SOIC 制造商:Cirrus Logic 功能描述:PFC Controller |
| CS1601H-FSZR | 制造商:Cirrus Logic 功能描述:IC PFC CONTROLLER DCM OCP (100KHZ) - Tape and Reel 制造商:Cirrus Logic 功能描述:IC PFC CTRLR BALLAST 8SOIC 制造商:Cirrus Logic 功能描述:PFC Controller |
| CS16034_STRADELLA-IP-28-T2 | 功能描述:LENSSQUARE28 POS100*100MM (D)9,2 制造商:ledil 系列:Stradella 零件状态:在售 类型:透镜 颜色:透明 LED 数:32 透镜样式:方形，带圆顶 透镜尺寸:100mm x 100mm 透镜透明度:- 光学图像:非对称 视角:- 配套使用/相关制造商:Cree，Lumileds，Osram 材料:丙烯酸 安装类型:螺钉 标准包装:78 |
发布紧急采购，3分钟左右您将得到回复。