- 您现在的位置：买卖IC网 > PDF目录10681 > CS5525-ASZ (Cirrus Logic Inc)IC ADC 16BIT W/4BIT LATCH 20SSOP PDF资料下载
参数资料
| 型号： | CS5525-ASZ |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 11/30页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT W/4BIT LATCH 20SSOP |
| 标准包装： | 66 |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 12.7mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，单极；1 个差分，双极 |
| 产品目录页面： | 755 (CN2011-ZH PDF) |
| 配用： | 598-1013-ND - EVAL BOARD FOR CS5525 |
| 其它名称： | 598-1107-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
CS5525 CS5526
DS202F5
19
Assuming a system can provide two known voltag-
es, equations can allow the user to manually com-
pute the calibration register’s values based on two
uncalibrated conversions. The offset and gain cali-
bration registers are used to adjust a typical conver-
sion as follows:
Rc = (Ru + Co>>4) * Cg / 223.
Calibration can be performed using the following
equations:
Co = (Rc0/G - Ru0) << 4
Cg = 223 * G
where G = (Rc1 - Rc0)/(Ru1-Ru0).
Note: Uncalibrated conversions imply that the gain and offset
registers are at default {gain register = 0x800000 (Hex) and
offset register = 0x000000 (Hex)}.
The variables are defined below.
V0
=
First calibration voltage
V1
=
Second calibration voltage (greater than V0)
Ru
=
Result of any uncalibrated conversion
Ru0
=
Result of uncalibrated conversion V0
(20-bit integer or 2’s complement)
Ru1
=
Result of uncalibrated conversion of V1
(20-bit integer or 2’s complement)
Rc
=
Result of any conversion
Rc0
=
Desired calibration result of converting V0
(20-bit integer or 2’s complement)
Rc1
=
Desired calibration result of converting V1
(20-bit integer or 2’s complement)
Co
=
Offset calibration register value (24-bit 2’s
complement)
Cg
=
Gain calibration register value
(24-bit integer)
>>
=
The shift right operator (e.g. x >>2 is x shift-
ed right 2 bits)
<<
=
The shift left operator (e.g. x<<2 is x
shifted left 2 bits)
Note: The shift operators are used here to align the decimal
points of words of various lengths. Data to the right of the
decimal point may be used in the calculations shown. For the
CS5525 all conversion results (Ru, Rc...) are 16 bits instead
of 20 bits. To get the equations to work correctly pad the 16
bit results with four zeros (on the right).
Calibration Tips
Calibration steps are performed at the output word
rate selected by the WR2-WR0 bits of the configu-
ration register. Since higher word rates result in
conversion words with more peak-to-peak noise,
calibration should be performed at lower output
word rates.
Also, to minimize digital noise near
the devices, the user should wait for each calibra-
tion step to be completed before reading or writing
to the serial port.
For maximum accuracy, calibrations should be per-
formed for offset and gain for each gain setting (se-
lected by changing the G2-G0 bits of the
configuration register). And if factory calibration is
performed using the system calibration capabilities
of the CS5525/26, the offset and gain register con-
tents can be read by the system microcontroller and
recorded in EEPROM. These same calibration
words can then be uploaded into the offset and gain
registers of the converters when power is first ap-
plied to the system, or when the gain range is
changed.
Two final tips include two ways to determine when
calibration is complete: 1) wait for SDO to fall. It
falls to logic 0 if the PF (Port Flag) bit of the con-
figuration register is set to logic 1; or 2) poll the DF
(Done Flag) bit in the configuration register which
is set at completion of calibration.
Whichever
method is used, the calibration control bits (CC2-
CC0) will return to logic 0 upon completion of any
calibration.
Limitations in Calibration Range
System calibration can be limited by signal head-
room in the analog signal path inside the chip as
discussed under the Analog Input section of this
data sheet. System calibration can also be limited
by the intrinsic gain errors of the instrumentation
amplifier and the modulator. For gain calibrations
相关PDF资料 |
PDF描述 |
|---|---|
| LT1715IMS#TR | IC COMPARATOR 150MHZ DUAL 10MSOP |
| AD8612ARUZ-REEL | IC COMP DUAL 4NS FAST 14-TSSOP |
| AD9609BCPZ-40 | IC ADC 10BIT 40MSPS LP 32LFCSP |
| AD7276BUJZ-500RL7 | IC ADC 12BIT 3MSPS TSOT23-6 |
| LT1720IMS8#PBF | IC COMPARATOR DUAL HS 3/5V 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS5525-ASZR | 功能描述:模数转换器 - ADC IC 16Bit Delta Sigma Multi-Range ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| CS5525-BP | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:16 BIT / 20 BIT MULTI RANGE ADC WITH 4 BIT LATCH |
| CS5525-BS | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:16 BIT / 20 BIT MULTI RANGE ADC WITH 4 BIT LATCH |
| CS5526 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:16 BIT / 20 BIT MULTI RANGE ADC WITH 4 BIT LATCH |
| CS5526-000 | 制造商:TE Connectivity 功能描述:S200-1-01 - Bulk |
发布紧急采购，3分钟左右您将得到回复。