- 您现在的位置：买卖IC网 > PDF目录10681 > CS5529-ASZ (Cirrus Logic Inc)IC ADC 16BIT W/6BIT LATCH 20SSOP PDF资料下载
参数资料
| 型号： | CS5529-ASZ |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 7/31页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT W/6BIT LATCH 20SSOP |
| 标准包装： | 66 |
| 位数： | 16 |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 3.5mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，单极；1 个差分，双极 |
| 产品目录页面： | 755 (CN2011-ZH PDF) |
| 配用： | 598-1015-ND - EVAL BOARD FOR CS5529 |
| 其它名称： | 598-1110-5 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
CS5529
DS246F5
15
Serial Port Initialization
The serial port is initialized to the command mode
whenever a power-on reset is performed or when
the port initialization sequence is completed. The
port initialization sequence involves clocking fif-
teen (or more) SYNC1 command bytes (0xFF) fol-
lowed by one SYNC0 command byte (0xFE). This
sequence places the chip in the command mode
where it waits until a valid command is received.
This function does not reset the internal registers to
their default settings. It only resets the serial port to
the command mode.
System Initialization
When power to the CS5529 is applied, the chip is
held in a reset condition until the 32.768 kHz oscil-
lator has started and a counter-timer elapses. Due to
the high Q of the 32.768 kHz crystal, the oscillator
takes 400-600 ms to start. The counter-timer counts
1002 oscillator clock cycles to make sure the oscil-
lator is fully stable. During this time-out period the
serial port logic is reset and the RV (Reset Valid)
bit in the configuration register is set to indicate
that a valid reset occurred. After a reset, the on-chip
registers are initialized to the following states and
the converter is placed in the command mode
where it waits for a valid command.
Note:
A system reset can be initiated at any time by
writing a logic 1 to the RS (Reset System) bit
in the configuration register. After a reset, the
RV (Reset Valid) bit is set until the
configuration register is read. The user must
then write a logic 0 to the RS bit to take the
part out of the reset mode.
Configuration Register
The configuration register is a 24 bit register used
to modify the functions of the ADC. The following
sections detail the functions of the bits in the con-
figuration register.
Latch Output Pins
The D3-D0 pins of the converter mimic the D21-
D18 bits of the configuration register. D3-D0 can
be used to control multiplexers and other digital
logic functions outside the converter. The D0-D3
outputs are powered from VD+ and DGND. Their
output voltage will be VD+ for a logic 1 and
DGND for a logic 0. The A1-A0 pins of the con-
verter mimic the D23-D22 bits of the configuration
register and can be used to control analog switches.
These outputs are powered from VA+ and VA-,
hence, their output voltage will be either VA+ for a
logic 1 or VA- for a logic 0.
All outputs can sink or source at least 1 mA, but it
is recommended to limit drive currents to less than
20
A to reduce self-heating of the chip.
Power Consumption
The CS5529 accommodates four power consump-
tion modes: normal, low power, standby, and sleep.
The normal mode, the default mode, is entered after
a power-on-reset and typically consumes 2.5 mW.
The low power mode is an alternate mode that re-
duces the consumed power to 1.4 mW. It is entered
by setting bit D16 (the low power mode bit) in the
configuration register to logic 1. Since the convert-
er’s noise and linearity performance improves with
increased power consumption, slightly degraded
noise or linearity performance should be expected
in the low power mode.
The final two modes are the power save modes.
These modes power down most of the analog por-
tion of the chip and stop filter convolutions. The
power save modes are entered whenever the Power
Save (0x81 hexadecimal) command is issued to the
serial port. The particular power save mode entered
depends on state of bit D4 (the power save select
bit) in the configuration register. If D4 is logic 0,
the converter enters the standby mode reducing the
power consumption to 1 mW. The standby mode
leaves the oscillator and the on-chip bias generator
Configuration Register:
000040(H)
Offset Register:
000000(H)
Gain Register:
400000(H)
相关PDF资料 |
PDF描述 |
|---|---|
| VI-22Z-MW-B1 | CONVERTER MOD DC/DC 2V 40W |
| AD7798BRUZ | IC ADC 16BIT SIG-DEL 3CH 16TSSOP |
| VI-22T-MY-B1 | CONVERTER MOD DC/DC 6.5V 50W |
| AD9281ARSZ | IC ADC 8BIT DUAL CMOS 28-SSOP |
| AD8564ARZ-REEL7 | IC COMPARATOR QUAD 7NS 16SOIC TR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS5529-ASZR | 功能描述:模数转换器 - ADC IC Prgrmbl Dlt Sigma ADC w/6-Bit Latch RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| CS5530 | 制造商:Texas Instruments 功能描述: |
| CS5530_0911 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:24-bit ADC with Ultra-low-noise Amplifier |
| CS5530A | 制造商:AMD 制造商全称:Advanced Micro Devices 功能描述:AMD Geode CS5530A Companion Device |
| CS5530A-UCE | 制造商:AMD 制造商全称:Advanced Micro Devices 功能描述:AMD Geode CS5530A Companion Device |
发布紧急采购，3分钟左右您将得到回复。